Abstract:The micro-mechanical behavior of lamellar structured Ti6Al4V alloy was studied upon a small strain of 4.5 % compressional loading. The strain and stress concentration is found highly related to individual crystallographic orientation, their size, shape and grain-grain interaction, which usually concentrated along grain boundaries (GBs) typically soft and hard GBs owing to the strong strain gradient incurred. The generated local plastic deformation forms ledges through dislocation accumulation which further activate large amount of Geometrically necessary dislocations (GNDs) to accomodate strain incompatibility. Both strain and stress is maximized at some triple points (TPs). EBSD and crystal plasticity (CP) simulation disclosed some long range meso-bands (about 45° to loading direction) across multi-grains and mini-bands within grain interiors (GIs) with concentrated strain behavior which demonstrate slip and ductile behavior of the Ti6Al4V material. Prismatic slip is found dominated the slip behavior of the Ti6AL4V alloy (mostly from surface dislocation activation) which is away from some findings of literature and largely determined by its low critical resolved shear stress (CRSS). Dislocation is observed emitted from high angle grain boundaries (HAGBs) while slip transmission is observed through both low (LAGBs) and HAGBs. The substructures (α-lamellae), a type of LAGBs allocated within α-colonies, have no significant effect to dislocation movement. Fatigue failure can be inferred from the early stage of micro-mechanical behavior mainly judged by the amount of accumulated plastic deformation and induced stress/strain distribution amont the surroundings. Crack may nucleate from easy prismatic slip, local strain accumulation induced by soft and hard grain clustering (either hard embedded in soft or vice versa usually start from some TPs and sharp corners), or some concentrated long range slip activities. Other than the surface dents induced failure, shearing, cleavage, multi-cleavage and intergranular patterns is presumed highly related to the local microstructure, including their relative size, shape, orientation and grain-grain interactions. The multiple crack origins deemed for reduce fatigue life of shot peened samples regardless of the surface compressional residual stress being generated. The work helps understand the micro-mechanical deformation behavior (down to dislocation level) of Ti6Al4V alloy. Their fatigue and fracture can be inferred from such early stage of strain/stress behavior considering microstructural heterogeneities for similar alloys.

Effects of the crystallographic and spatial orientation of α lamellae on the anisotropic in-situ tensile behaviors of additive manufactured Ti–6Al–4V

Revealing interface-assisted plastic anisotropy <i>via in situ</i> transmission electron microscopy tension of lamellar TiAl

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

Deformations of Ti-6Al-4V additive-manufacturing-induced isotropic and anisotropic columnar structures: Insitu measurements and underlying mechanisms

Multiple Α Sub-Variants and Anisotropic Mechanical Properties of an Additively-Manufactured Ti-6Al-4V Alloy

In-Situ Tensile Deformation Behavior Of As-Built Laser Direct Metal Deposited Ti-6al-4v Alloy At 200 Degrees C

Microstructural and texture evolution investigation of laser melting deposited TA15 alloy at 500?C using in-situ EBSD tensile test

Effects of the morphology of grain boundary α-phase on the anisotropic deformation behaviors of additive manufactured Ti–6Al–4V

In-situ investigation on the anisotropic behavior of the additively manufactured dual-phase Ti-6Al-4V alloy

Mechanical Properties Anisotropy of Ti−6Al−4V Alloy Fabricated by Β Forging

On the texture and mechanical property anisotropy of Ti6Al4V alloy fabricated by powder-bed based laser additive manufacturing

Effect of Sample‐Build Orientation on the Tensile Deformation and Properties of Ti6Al4V Processed by Laser Powder Bed Fusion

In Situ Electron Backscatter Diffraction Study of Deformation Inhomogeneity under Uniaxial Tension of Laser Melting Deposited TA15 Alloy

Effect of Solution Treatment on Microstructure, Texture, and Anisotropy of Mechanical Properties in TA10 (Ti-0.3Mo-0.8Ni) Sheet

Micro-mechanical behavior of lamellar structured Ti6Al4V alloy upon compression via experimental and crystal plasticity study

The role of defects and characterisation of tensile behaviour of EBM Additive manufactured Ti-6Al-4V: An experimental study at elevated temperature

In Situ Tensile Observation of the Effect of Annealing on Fracture Behavior of Laser Additive Manufactured Titanium Alloy

Influence of microstructural and crystallographic inhomogeneity on tensile anisotropy in thick-section Al-Li-Cu-Mg plates

Experimental and Crystal Plasticity Finite Element Investigations of Plastic Anisotropy in Additively Manufactured Ti6Al4V Alloy

Transverse texture weakening and anisotropy improvement of Ti-6Al-4V alloy sheet via asymmetric rolling and static recrystallization annealing

Selective Laser Melting of Ti-5Al-2.5Sn Alloy with Isotropic Tensile Properties: the Combined Effect of Densification State, Microstructural Morphology, and Crystallographic Orientation Characteristics