Abstract:Al-Mg-Si alloys fabricated by additive manufacturing (AM) are known to suffer from the coarse columnar microstructure, which usually causes severe hot cracking and anisotropy in mechanical properties. Introducing potent nucleants to promote columnar to equiaxed transition (CET) is an efficient method to solve this problem. However, nanoscale nucleant particles are prone to agglomerate and form clusters during high-temperature AM, which are detrimental to the ductility. In this work, in the AA6061 fabricated by directed energy deposition (DED), we designed a novel approach to alleviate the agglomeration of TiB 2 particles by adopting interlayer pause (IP) strategy on the basis of TiB 2 nucleant addition. Resultantly, due to the discontinuous heat input interrupted by IP and thus a reduced heat accumulation, dispersed fine TiB 2 particles can be achieved, which reduce the stress concentration and allow for a good metallurgical binding. Moreover, these dispersed fine TiB 2 particles, (a) effectively promote the CET by providing numerous heterogeneous nucleation sites, resulting in an ultra-fine fully-equiaxed grain microstructure (~ 21 μm) with a reduced texture; (b) significantly inhibit the formation of pores, reducing both their density and size. Consequently, crack-free high-performance DEDed AA6061 without anisotropy in mechanical properties are successfully fabricated, achieving high strength and high ductility at T6-treated state along both the vertical direction (YS: 266 ± 2 MPa, EL: 8 ± 1%) and the horizontal direction (YS: 262 ± 2 MPa, EL: 7 ± 1%), simultaneously. This combination of nucleant addition and deliberately-controlled IP strategy is expected to be applicable to a wide range of wrought aluminum alloys (e.g. 2xxx and 7xxx) fabricated by AM.

Effect of Grain Boundary Widmanstätten Α Colony on the Anisotropic Tensile Properties of Directed Energy Deposited Ti-6Al-4V Alloy

Enhancing Ductility of Titanium Matrix Composites by Multimodal Α-Grains

Effects of the morphology of grain boundary α-phase on the anisotropic deformation behaviors of additive manufactured Ti–6Al–4V

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

Hierarchical Anisotropic Material Response of Directed Energy Deposited (DED) Ti-6Al-4V alloy

Modification of Microstructure and Mechanical Properties for Twin-Wire Directed Energy Deposition-Arc Fabricated Ti-48al-2cr-2nb Alloys Via Current Regulation

Wire-fed electron beam directed energy deposition of Ti–6Al–2Zr–1Mo–1V alloy and the effect of annealing on the microstructure, texture, and anisotropy of tensile properties

In-Situ Tensile Deformation Behavior Of As-Built Laser Direct Metal Deposited Ti-6al-4v Alloy At 200 Degrees C

Isotropic and improved tensile properties of Ti-6Al-4V achieved by in-situ rolling in direct energy deposition

Investigation of α phase evolution and tensile fracture behavior of Ti5Al2Sn2Zr4Mo4Cr alloy fabricated by directed energy deposition

Effects of the crystallographic and spatial orientation of α lamellae on the anisotropic in-situ tensile behaviors of additive manufactured Ti–6Al–4V

Effect of Microstructural Characteristics on Fracture Toughness in Direct Energy Deposited Novel Ti-6Al-4V-1Mo Alloy

Effect of Lamellae Orientation on Tensile Properties of Directionally Solidified Ti–46Al–0.5W–0.5Si Alloy

Spatially heterogeneous microstructure in in-situ TiO-reinforced Ti6Al4V/316L functionally graded material fabricated via directed energy deposition

Directed energy deposition of Al-Mg-Si alloys with fully-equiaxed microstructure and isotropic high strength/ductility

Grain boundary engineering of AL6XN super-austenitic stainless steel: Distinctive effects of planar-slip dislocations and deformation twins

Controllable Mechanical Anisotropy of Selective Laser Melted Ti6Al4V: A New Perspective into the Effect of Grain Orientations and Primary Grain Structure

Influence of Grain Size on Electrically Assisted Tensile Behavior of Ti-6Al-4V Alloy

Investigation on Anisotropic Mechanical Behavior of Ti-6Al-4V Alloy Via Schmid Factor and Kernel Average Misorientation Distribution

Microstructure Modification of Twin-Wire Directed Energy Deposition-Arc Fabricated Γ-Tial Alloy Via Deposition Current Control

New insights into ductility improvement of a nickel-based superalloy through grain boundary engineering