Abstract:Additive manufacturing (AM) of high-entropy alloys (HEAs), such as CoCrFeMnNi, is of high interest owing to their potential applications for extreme conditions (e.g., cryogenic environment). However, a major drawback of additively manufactured (AMed) metallic components is their poor and anisotropic mechanical properties, which primarily originate from the presence of metallurgical defects and coarse columnar grains. This study herein aims to (i) manipulate directed energy deposition (DED) AM parameters towards densification and (ii) suppress the formation of coarse columnar grains in DED AMed CoCrFeMnNi HEA. First, the effects of laser powers and laser scan speeds on the formation of various metallurgical defects in the DED AMed CoCrFeMnNi samples were investigated. Contrary to the laser powder bed fusion (L-PBF) AMed CoCrFeMnNi HEAs which were reported to form lack-of-fusion defects in the regime of low laser powers and high laser scan speeds, the lack-of-fusion defects in DED AMed CoCrFeMnNi HEAs tend to form in the regime of high laser powers and low laser scan speeds. This abnormal observation was rationalized by recourse to the resultant large layer thickness and hence insufficient melting. Cracking was observed in the regime of high laser scan speeds, and these cracks were classified into solidification cracks based on the observation of the intruding cellular/dendritic features on the cracked surface. High angle grain boundaries were found to be more sensitive to solidification cracking and the inherent mechanisms were discussed. Through such a high throughput library of samples, a printability map and near-full density were achieved for DED AMed CoCrFeMnNi HEAs. Second, for the grain structure control, contrary to the previous works that tried to manipulate the solidification conditions or introduce the secondary heterogenous particles, the current paper employed ultrasonic-assisted DED AM processing of CoCrFeMnNi HEA. Despite the measured lowered cooling rate, the coarse columnar grains were replaced by finer equiaxed grains in the presence of ultrasound, i.e., the average grain size decreases from 140 to 44 mu m. The formation of fine equiaxed grains were rationalized by the combined effects of the ultrasonic-facilitated dendrite fragmentation as heterogenous nucleation sites and the enhanced liquid supercooling in the columnar front. As a direct result, the tensile yield strength of the ultrasonic-assisted DED AMed CoCrFeMnNi HEA increases by similar to 17%, with no obvious tensile ductility drop. The strength increase was well explained by the grain refinement effect based on the classic Hall-Petch relationship. These findings provide opportunities to additively manufacture highperformance and complex-geometry HEAs components for critical applications.

Directed energy deposition of Al-Mg-Si alloys with fully-equiaxed microstructure and isotropic high strength/ductility

Enhancing Strength and Ductility in High Nb-containing TiAl Alloy Additively Manufactured Via Directed Energy Deposition

Effect of in-situ synthesized TiC particles on microstructure and mechanical properties of directed energy deposited AA2219 Al-Cu alloy

Nanoscale Engineering of Low-Misfit TiB2/Al3(Sc,Zr)/α-Al Multi-Interface to Improve Strength-Ductility Synergy for Direct Energy Deposited Aluminum Alloy

Microstructure and Mechanical Properties of Tic-Particle Reinforced Aa2219 Al-Cu Alloy Fabricated Via Directed Energy Deposition

In-situ grain structure control in directed energy deposition of Ti6Al4V

Nanoscale engineering of low-misfit TiB 2 /Al 3 (Sc,Zr)/α-Al multi-interface to improve strength-ductility synergy for direct energy deposited aluminum alloy

Enhanced Strength and Ductility of A356 Alloy Due to Composite Effect of Near-Rapid Solidification and Thermo-Mechanical Treatment

Directed Energy Deposition Additive Manufacturing of CoCrFeMnNi High-Entropy Alloy Towards Densification, Grain Structure Control and Improved Tensile Properties

Tailoring Grain Morphology in Ti-6Al-3Mo Through Heterogeneous Nucleation in Directed Energy Deposition

Isotropic and improved tensile properties of Ti-6Al-4V achieved by in-situ rolling in direct energy deposition

Research on Microstructure and Mechanical Properties of Ti–6Al–4V ELI Fabricated by Hybrid Directed Energy Deposition with In-Situ Rolling and Annealing

The Microstructure Tailoring and Property Improving of Directed Energy Deposited Al-Zn-Mg-Cu Alloy Modified with Various Si and ZrO2 Contents

Wire-Arc Directed Energy Deposition of Aluminum Alloy 7075 with Dispersed Nanoparticles

Evolution of microstructure and mechanical properties in the molten pool of γ-TiAl alloy synthesized in situ by dual-wire-fed electron beam directed energy deposition.

Investigations of the processing–structure–performance relationships of an additively manufactured AlSi10Mg alloy via directed energy deposition

Microstructure evolution and tensile property of TiAl alloy using continuous direct energy deposition technique

Phase transformation and microstructural evolution in Al-Mn-Fe-Si 3104 aluminum alloy made by laser directed energy deposition

Microstructure and mechanical properties of Al-Zn-Mg-Cu alloy fabricated by multi-wire arc-based directed energy deposition

Composition fine-tuning for directed energy deposition of Ti-6Al-4V

Tailoring the mechanical properties and thermal stability of additive manufactured micro-alloyed Al-Cu alloy via multi-stage heat treatment