Abstract:Directed energy deposition (DED) process can enable rapid and low-cost manufacturing of large-scale high-strength AA2219 Al-6.3 wt%Cu alloy components, displaying broad prospects for structural lightweighting in aerospace applications. However, a high tendency to prominent porosity defects and inhomogeneous layered microstructure are intrinsically present in DED-processed Al-Cu alloy, leading to significant performance degradation and anisotropy. Herein, we demonstrate a robust DED process to fabricate high-quality formed AA2219 alloy deposits, based on in-situ synthesized TiC-containing wires and an ultrasonic-frequency pulsed (UFP) arc. The effects of in-situ synthesized submicron-scale TiC particles (average diameter 0.7 ± 0.4 μm) in microstructural evolution and mechanical performance were comparatively investigated through multi-scale microstructural characterization and mechanical property measurement. The introduction of TiC particles into the as-deposited AA2219 component results in a homogeneous refined equiaxed microstructure with an average α-Al grain diameter of 23.4 ± 2.9 μm, and a dramatical elimination of porosity defects. After undergoing a T6 solution and aging treatment, the TiC-reinforced AA2219 deposit demonstrates excellent resistance against grain coarsening, porosity defects growth, and particle segregation. Moreover, the introduced TiC particles lead to a noticeably enhanced precipitation hardening behavior. A homogeneous precipitation microstructure of dispersed θ′-Al 2 Cu particles with an average diameter of 84.1 ± 34.5 nm and a high fraction of 9.8 ± 2.5 vol% was obtained in the heat-treated AA2219 deposit. Based on the as-built multiscale homogeneous microstructure, the heat-treated deposit embedded with TiC particles exhibits a synergy of unprecedented tensile strength of 501 ± 14 MPa and excellent ductility of 9.6 ± 3.3%.

Composition fine-tuning for directed energy deposition of Ti-6Al-4V

Effects of Fe Contents on the Microstructure and Precipitate of Ti–Al–V Alloys Prepared by Direct Energy Deposition

Microstructure and Mechanical Properties of Ti60-Ti2alnb Functionally Graded Materials Fabricated by Laser Directed Energy Deposition

Achieving ultra-high strength rapidly in Ti-3Al-8V-6Cr-4Mo-4Zr alloy processed by directed energy deposition

Effect of T6 heat treatment on microstructure and mechanical properties of Al–18Si–10Cu–10Ni–5Mn–5Mg alloy prepared by laser-directed energy deposition

Directed energy deposition of Al-Mg-Si alloys with fully-equiaxed microstructure and isotropic high strength/ductility

Effect of in-situ synthesized TiC particles on microstructure and mechanical properties of directed energy deposited AA2219 Al-Cu alloy

Microstructure and mechanical properties of a newly developed Ti-6Al-2Mo-2Sn-2Zr-2Cr-2V alloy fabricated by laser directed energy deposition

Wire-fed electron beam directed energy deposition of Ti–6Al–2Zr–1Mo–1V alloy and the effect of annealing on the microstructure, texture, and anisotropy of tensile properties

Evolution of microstructure and mechanical property of Ti-47Al-2Cr-2Nb intermetallic alloy by laser direct energy deposition: From a single-track, thin-wall to bulk

Balance of strength and ductility for laser directed energy deposited Ta-containing Ti6Al4V via solution and aging treatment

Ti6Al4V Thin Walls Production using Laser Directed Energy Deposition (L-DED) Process

Effects of Conventional Interweaving and Secondary Deposition on the Microstructure and Properties of Ti6Al4V/AA2024 Alloy Component Fabricated by Laser-Directed Energy Deposition

Influence of Tungsten Addition on Microstructure and Tensile Properties of Ti6Al4V Fabricated by Laser-Directed Energy Deposition

Evolution of microstructure and mechanical properties in the molten pool of γ-TiAl alloy synthesized in situ by dual-wire-fed electron beam directed energy deposition.

Microstructure and Mechanical Properties of An Ultrahigh-strength Titanium alloy Ti-4.5Al-5Mo-5V-6Cr-1Nb Prepared Using Laser Directed Energy Deposition and Forging: A Comparative Study

Isotropic and improved tensile properties of Ti-6Al-4V achieved by in-situ rolling in direct energy deposition

An exploratory study on biocompatible Ti-6Mn-4Mo alloy manufactured by directed energy deposition

Enhanced Microstructure and Wear Resistance of Ti–6Al–4V Alloy with Vanadium Carbide Coating via Directed Energy Deposition

Spatially heterogeneous microstructure in in-situ TiO-reinforced Ti6Al4V/316L functionally graded material fabricated via directed energy deposition

Investigation of α phase evolution and tensile fracture behavior of Ti5Al2Sn2Zr4Mo4Cr alloy fabricated by directed energy deposition