Abstract:Directed energy deposition (DED) process can enable rapid and low-cost manufacturing of large-scale high-strength AA2219 Al-6.3 wt%Cu alloy components, displaying broad prospects for structural lightweighting in aerospace applications. However, a high tendency to prominent porosity defects and inhomogeneous layered microstructure are intrinsically present in DED-processed Al-Cu alloy, leading to significant performance degradation and anisotropy. Herein, we demonstrate a robust DED process to fabricate high-quality formed AA2219 alloy deposits, based on in-situ synthesized TiC-containing wires and an ultrasonic-frequency pulsed (UFP) arc. The effects of in-situ synthesized submicron-scale TiC particles (average diameter 0.7 ± 0.4 μm) in microstructural evolution and mechanical performance were comparatively investigated through multi-scale microstructural characterization and mechanical property measurement. The introduction of TiC particles into the as-deposited AA2219 component results in a homogeneous refined equiaxed microstructure with an average α-Al grain diameter of 23.4 ± 2.9 μm, and a dramatical elimination of porosity defects. After undergoing a T6 solution and aging treatment, the TiC-reinforced AA2219 deposit demonstrates excellent resistance against grain coarsening, porosity defects growth, and particle segregation. Moreover, the introduced TiC particles lead to a noticeably enhanced precipitation hardening behavior. A homogeneous precipitation microstructure of dispersed θ′-Al 2 Cu particles with an average diameter of 84.1 ± 34.5 nm and a high fraction of 9.8 ± 2.5 vol% was obtained in the heat-treated AA2219 deposit. Based on the as-built multiscale homogeneous microstructure, the heat-treated deposit embedded with TiC particles exhibits a synergy of unprecedented tensile strength of 501 ± 14 MPa and excellent ductility of 9.6 ± 3.3%.

Microstructure and mechanical properties of Al-Zn-Mg-Cu alloy fabricated by multi-wire arc-based directed energy deposition

Enhanced High-Temperature Strength and Ductility of Wire Arc Additive Manufactured Al-Ce-Mg Alloys with Fine Α-Al/al11ce3 Eutectics

A comparative study on microstructure and mechanical properties of wire-arc directed energy deposited Al–Zn–Mg–Cu alloy based on the cold metal transfer technology

Microstructure and properties research of Al-Zn-Mg-Cu alloy with high strength and high elongation fabricated by wire arc additive manufacturing

Achieving excellent strength-ductility combination of Al-aided Mg-Gd-Al-Zr-Zn alloys fabricated by cold metal transfer-based wire-arc directed energy deposition via uniform equiaxed grains and multiple precipitates

Microstructure and mechanical properties of a dilute Mg-Gd-Y-Zr alloy fabricated using wire-arc directed energy deposition additive manufacturing

Directed energy deposition of Al-Mg-Si alloys with fully-equiaxed microstructure and isotropic high strength/ductility

Effect of in-situ synthesized TiC particles on microstructure and mechanical properties of directed energy deposited AA2219 Al-Cu alloy

Wire arc additive manufacturing of Al-Zn-Mg-Cu alloy: Microstructures and mechanical properties

Microstructure and Mechanical Properties of an Advanced Ag-Microalloyed Aluminum Crossover Alloy Tailored for Wire-Arc Directed Energy Deposition

Novel high-strength Al-Cu-Cd alloy fabricated by arc-directed energy deposition: precipitation behavior of the Cd phase and grain evolution

Microstructure and mechanical properties of wire arc additive manufactured ZL205A alloy

The microstructures and mechanical properties of Al-Zn-Mg-Cu-Si-Zr alloy: A comparison between directed energy deposition and laser powder bed fusion

Microstructure and mechanical properties of Mg-Nd-Zn-Zr alloy fabricated by TIG-based wire - arc directed energy deposition with pulsed current

Microstructure evolution and mechanical properties of Al–Cu–Mn–Cd alloy fabricated by CMT-wire arc additive manufacturing

Microstructures and Properties of Al-Mg Alloys Manufactured by WAAM-CMT

Enhancing strength, ductility, and fatigue performance of Al-Zn-Mg-Cu-Sc-Zr alloy using a hybrid approach: Wire-arc directed energy deposition and interlayer friction stir processing

Tailoring the mechanical properties and thermal stability of additive manufactured micro-alloyed Al-Cu alloy via multi-stage heat treatment

Integrated control mechanism of ultrasound and ZrO2 particles on differential microstructures for the wire arc additive manufacturing

Microstructure and mechanical properties of a newly developed Ti-6Al-2Mo-2Sn-2Zr-2Cr-2V alloy fabricated by laser directed energy deposition

Al–Zn–Mg–Cu alloy with both high strength and high plasticity fabricated with wire arc additive manufacturing