Abstract:In this study, three different levels of laser energy inputs (Ev) were used for selective laser melting of Ti-5Al-2.5Sn alloy and the as-deposited tensile properties along the vertical direction with respect to deposition layers were found to be statistically identical to those along the horizontal direction for all the samples. Densification states, microstructures, and crystallographic orientation characteristics of the different samples, as well as their contributions to the isotropic properties were researched. The results first indicated that near spherical pores would form at the relatively high Ev (208 J/mm(3)) whereas lack-of-fusion defects would generate at the relatively low Ev (51 J/mm(3)). When the moderate Ev (167 J/mm(3)) was used, samples with very few defects could be fabricated. Then, it was seen that samples built at 51 and 167 J/mm(3) presented a martensite (alpha')-dominated microstructure in which the boundaries of columnar prior-beta were decorated by grain-boundary alpha (alpha(GB)). When Ev increased to 208 J/mm(3), a duplex microstructure composed of alpha' and massive alpha (alpha(M)) would form within prior-beta matrix of the as-deposited samples. An overall increasing trend in prior-beta's width with the increase of Ev was also identified. Afterwards, it was proved that there was no strong texture within all the samples and this was one cause of the isotropic properties. Besides, for samples built at 51 J/mm(3), the negative influence of lack-of-fusion on vertical properties cooperated with the adverse effect of large quantities of a GB on horizontal properties, promoting the obtainment of isotropic properties. For samples built at 167 J/mm(3), not only the high densification degree but also the significantly increase in prior-beta's width and the resultant decrease in alpha(GB) 's content helped to eliminate significant anisotropy. For samples built at 208 J/mm(3), both the near spherical pores which resulted in near-identical bearing areas on different sections and the absent of alpha(GB) contributed to the isotropic properties. This paper can provide some basis for the laser additive manufacturing of titanium products with isotropic properties.

Effect of Lamellae Orientation on Tensile Properties of Directionally Solidified Ti–46Al–0.5W–0.5Si Alloy

Revealing interface-assisted plastic anisotropy <i>via in situ</i> transmission electron microscopy tension of lamellar TiAl

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

On the Orientation Relationship Between Ti5Si3 Precipitates and B2 Phase in a Ti-47Al-2W-0.5Si Alloy

Thermal stability and its effects on the mechanical properties of rapidly solidified Al-Ti alloys

In-Situ Tensile Deformation Behavior Of As-Built Laser Direct Metal Deposited Ti-6al-4v Alloy At 200 Degrees C

Tensile properties and fracture toughness of TiAl alloys with controlled microstructures

Study of tensile properties and fracture mechanisms of fully lamellar TiAl based alloy

Temperature-dependent Mechanical Properties and Fracture Behavior of Directionally Solidified Ti47Al2Cr2Nb Alloy

Study on improving directional microstructure of Ti44Al6Nb1Cr alloy by continuous regional phase transformation

Optimizing microstructure and mechanical properties of directionally solidified Ti44Al6Nb1Cr2V alloy by directional heat treatment

Microstructure Evolution and Mechanical Properties of a Directionally Solidified Nb-Ti-Si-Cr-Al-Hf-Dy Alloy

Controlling lamellar orientation of Ti-47.5Al-5Nb-2.5V-1Cr alloy by conventional casting

Drastic enhancement in hot-workability and microstructural refinement of TiAl alloys via martensitic transformation: A comparative study

Effects of the crystallographic and spatial orientation of α lamellae on the anisotropic in-situ tensile behaviors of additive manufactured Ti–6Al–4V

Breaking the high-temperature strength-ductility trade-off in TiAl alloys through microstructural optimization

Effect of Initial Orientation on the Anisotropy in Microstructure and Mechanical Properties of 2195 Al-Li Alloy Sheet during Hot Tensile Deformation

An investigation of ductile fracture behavior of Ti6Al4V alloy fabricated by selective laser melting

Selective Laser Melting of Ti-5Al-2.5Sn Alloy with Isotropic Tensile Properties: the Combined Effect of Densification State, Microstructural Morphology, and Crystallographic Orientation Characteristics

Effect of Sample‐Build Orientation on the Tensile Deformation and Properties of Ti6Al4V Processed by Laser Powder Bed Fusion

Investigation of macro/microstructure evolution and mechanical properties of directionally solidified high-Nb TiAl-based alloy