Abstract:TiAl intermetallic alloys have attracted considerable attention in aerospace applications over the last few decades owing to their low density and superior mechanical properties at high temperatures. However, these alloys are also known as difficult-to-machine materials that hinder efficient manufacturing. This study presents a systematic investigation on the machinability of TiAl alloys with three types of microstructures obtained by different heat treatment parameters. These were classified as near-gamma (NG), duplex (DP), and fully lamellar (FL). The machinability was evaluated based on the cutting forces and machined surface roughness. The material with α2/γ lamellar structures (FL) exhibited the lowest cutting force (3.21 N). However, produced a rougher surface (80 nm Ra) as compared to the NG microstructure (4.69 N and 47 nm Ra). Electron backscattering diffraction (EBSD) evaluation of the primary deformation zone in the cutting chips revealed that insufficient heat energy was converted from plastic deformation for recrystallization or β+γ→α2 phase transformation to occur. This indicated that the deformation mechanisms were significantly dependent upon the plasticity. The NG microstructure demonstrated a higher degree of plasticity in the primary deformation zone, which was attributed to the combined effect of super-dislocation decomposition, ordinary dislocation slip, and refined mechanical twins with preferred orientation along the < 11 2 ¯ > {111} crystallographic orientation. Conversely, the FL microstructure exhibited brittleness during chip formation due to the weak bonding force between hexagonal α2 and tetragonal γ phases that led to preferential micro-cracking along each interface. Reducing the crystal orientation is conductive for improving machined surface quality. The notion of enhanced brittleness to explain the reduction in cutting forces due to the dissipation of energy through fracture was supported with numerical simulations. Microscopic evaluation was used to understand the deformation differences of the equiaxed γ grain and α2/γ lamellar microstructure during micro-cutting. Additionally, enhanced the understanding of the deformation mechanism of these multi-phase alloys.

Drastic enhancement in hot-workability and microstructural refinement of TiAl alloys via martensitic transformation: A comparative study

Tailoring microstructure and mechanical performance of a β-solidifying TiAl alloy via martensitic transformation

Breaking the high-temperature strength-ductility trade-off in TiAl alloys through microstructural optimization

Microstructure Regulation and Strength-Elongation Synergy of the Near Alpha TZAM Alloy Via Thermomechanical Processing

Thermal stability and its effects on the mechanical properties of rapidly solidified Al-Ti alloys

Tensile properties and fracture toughness of TiAl alloys with controlled microstructures

Evading the strength-ductility trade-off at room temperature and achieving ultrahigh plasticity at 800°C in a TiAl alloy

Study on the Relationship Between Microstructure and Mechanical Property in a Metastable Β Titanium Alloy

Effect of Hot-Pressing Temperature on Microstructure and the Improvement of Residual Al on Tensile Ductility of Ti/Al3Ti Heterogeneous Structure

Unraveling hot deformation behavior and microstructure evolution of nanolamellar TiAl/Ti3Al composites

Microstructure and microhardness evolution of Ti-10V-2Fe-3Al alloy under tensile/torsional deformation modes

Hot Deformation Behavior and Microstructural Evolution of a Novel β-Solidifying Ti-43Al-3Mn-2Nb-0.1Y Alloy

Microstructural characteristics and recrystallization mechanism of Ti-6.5Al–2Zr–1Mo–1V alloy during two-stage hot deformation

Microstructural Evolution and Deformation Micromechanism of Cold-Deformed TiNi-Based Alloys

Martensite colony engineering: A novel solution to realize the high ductility in full martensitic 3D-printed Ti alloys

Metastable microstructure evolution and grain refinement in a Low-Ta containing γ-TiAl alloy through heat treatment

Microstructural evolution and FCC twinning behavior during hot deformation of high temperature titanium alloy Ti65

Microstructural modulation of TiAl alloys for controlling ultra-precision machinability

Revealing the Effect of α' Decomposition on Microstructure Evolution and Mechanical Properties in Ti80 Alloy

Martensitic structure evolution during deformation and its correlation with solution temperature in metastable β titanium alloys

Effect of hydrogen on deformation induced phase transformation and hot workability of Ti2AlN/Ti46Al4Nb1Mo composites