Abstract:The optimum balance between mechanical properties and gloss of acrylonitrile–styrene–acrylate resin by controlling poly(n‐butyl acrylate) particle size. Preparation of acrylonitrile–styrene–acrylate (ASA) with high gloss and superior impact properties is still challenging. Here, we developed a new strategy for the preparation of ASA resins by a selective redox initiation method based on a semi‐continuous emulsion polymerization technique. A series of ASA core‐shell impact modifiers were firstly obtained by grafting styrene (St) and acrylonitrile (AN) onto poly(n‐butyl acrylate) (PBA) seeded latexes of different sizes. The ASA core‐shell impact modifier was then used to toughen the styrene–acrylonitrile copolymer (SAN). The synergistic effects between the single particle size of the rubber phase and different particle sizes were systematically investigated, and the mechanical properties of SAN‐toughened resins at various particle sizes of the rubber phase were analyzed. The results revealed that toughened SAN with small particle sizes possessed better gloss, and the impact strength of the doped small‐particle toughened SAN was much higher than that of the single particle size toughened SAN. The ASA graft powders synthesized from large particle PBA (particle size 316 nm) and small particle PBA (particle size 99 nm), respectively, were mixed at a 50/50 ratio and blended with SAN resin, a gloss level reaching 95, and an impact performance of 275 J/m values almost twice those of a single particle size toughened SAN. Highlights Acrylonitrile–styrene–acrylate resins with an impact strength of 275 J/m and gloss of 95 were prepared. The balance between mechanical properties and gloss of acrylonitrile–styrene–acrylate resin was obtained. Polymerization was initiated at low temperature.

Acrylonitrile‐styrene‐acrylate Particles with Different Acrylonitrile Contents for Improving the Toughness of Poly(vinyl Chloride) Resin

Acrylonitrile-Styrene-Acrylate Particles with Different Microstructure for Improving the Toughness of Poly(styrene-co-acrylonitrile) Resin

Morphology and mechanical properties of Acrylonitrile-styrene-acrylate toughened plastics with block copolymer chain structure: Acrylonitrile-styrene-acrylate (ASA) toughened plastics with block copolymer chain structure

Study of Poly(vinyl Chloride)/acrylonitrile–styrene–acrylate Blends for Compatibility, Toughness, Thermal Stability and UV Irradiation Resistance

Synthesis of ACR/nanometer SiO2 Composite Particles and Their Tonghening Effect on PVC

Achieving optimum balance between mechanical properties and gloss of acrylonitrile–styrene–acrylate resin through control of rubber particle size distribution

Effect of Acrylate Toughening Agent on the Impact and Fusion Characteristics of PVC

Mechanical and Morphological Properties and Deformation Mechanisms of Acrylonitrile-Butadiene-Styrene/Poly(ϵ-Caprolactone) Blends with Varied Matrix Composition

Compatibilizing and toughening of the styrene and acrylonitrile copolymer and core‐shell impact modifier obtained by agglomerate technologies

Synthesis of ACR Impact Modifier with PVC Shell and Its Toughening Efficiency on PVC

Toughening Of Polyamide-6 With A Maleic Anhydride Functionalized Acrylonitrile-Styrene-Butyl Acrylate Copolymer

Influence of the Tert‐dodecyl Mercaptan Content in Poly(acrylonitrile‐butadiene‐styrene) on Properties of Chlorinated Polyvinyl Chloride/poly(acrylonitrile‐butadiene‐styrene) Blends

Core-Shell Particles Of Poly(Methyl Methacrylate)-Block-Poly(N-Butyl Acrylate) Synthesized Via Reversible Addition-Fragmentation Chain-Transfer Emulsion Polymerization And The Polymer'S Application In Toughening Polycarbonate

Toughening Effect of Poly(Ethene-Co-1-Butene)-Graft-Methyl Methacrylate and Acrylonitrile on Styrene-Acrylonitrile Copolymer (San)

Effects of the Reinforcement and Toughening of Acrylate Resin/Caco3 Nanoparticles on Rigid Poly(Vinyl Chloride)

Toughening of PA6 with MAH Functionalized Acrylate-styrene-acrylonitrile Copolymer

Variation of core-shell structural particles and their toughening behavior in poly (vinyl chloride) (PVC) matrix

Properties of Poly(butylene Terephthalate)/bisphenol A Polycarbonate Blends Toughening with Epoxy-Functionalized Acrylonitrile–Butadiene–Styrene Particles

Investigation of the Properties of Epoxy-Functionalized Acrylonitrile-butadiene-styrene Toughened Poly (butylene Terephthalate) and Its Blends

Effect of Hyperbranched Poly(amine-ester) Grafted Nano-SiO_2 on Reinforcement and Toughness of PVC

Morphology and Mechanical Behaviors of Rigid Organic Particles Reinforced Polycarbonate