Abstract:Glycidyl methacrylate functionalized acrylonitrile-butadiene-styrene (ABS-g-GMA) particles were prepared and used to toughen polylactide (PLA). The characteristic absorption at 1728 cm(-1) of the Fourier transform infrared spectra indicated that glycidyl methacrylate (GMA) was grafted onto the polybutadiene phase of acrylonitrile-butadiene-styrene (ABS). Chemical reactions analysis indicated that compatibilization and crosslinking reactions took place simultaneously between the epoxy groups of ABS-g-GMA and the end carboxyl or hydroxyl groups of PLA and that the increase of GMA content improved the reaction degree. Scanning electron microscopy results showed that 1 wt % GMA was sufficient to satisfy the compatibilization and that ABS-g-GMA particles with 1 wt % GMA dispersed in PLA uniformly. A further increase of GMA content induced the agglomeration of ABS-g-GMA particles because of crosslinking reactions. Dynamic mechanical analysis testing showed that the miscibility between PLA and ABS improved with the introduction of GMA onto ABS particles because of compatibilization reactions. The storage modulus decreased for the PLA blends with increasing GMA content. The decrease in the storage modulus was due to the chemical reactions in the PLA/ABS-g-GMA blends, which improved the viscosity and decreased the crystallization of PLA. A notched impact strength of 540 J/m was achieved for the PLA/ABS-g-GMA blend with 1 wt % GMA, which was 27 times than the impact strength of pure PLA, and a further increase in the GMA content in the ABS-g-GMA particles was not beneficial to the toughness improvement. (C) 2011 Wiley Periodicals, Inc. J Appl Polym Sci 122:2992-2999, 2011

Toughening of PA6 with MAH Functionalized Acrylate-styrene-acrylonitrile Copolymer

Toughening Of Polyamide-6 With A Maleic Anhydride Functionalized Acrylonitrile-Styrene-Butyl Acrylate Copolymer

Preparation and Characterization of Maleic Anhydride Compatibilized Poly(lactic acid)/Bamboo Particles Biocomposites

Effect of Reactive Group Types on the Properties of Core-Shell Modifiers Toughened PA6

Relationship between structure and properties in high-performance PA6/SEBS-g-MA/(PPO/PS) blends: The role of PPO and PS

Research on effect of ABS,MAH,DCP on property of PA6/ABS blend

Toughening of Polyamide‐6 with Little Loss in Modulus by Block Copolymer Containing Poly(styrene‐alt‐maleic Acid) Segment

Modification of the Grafting Character to Prepare PA6/ABS-g-MA Blends with Higher Toughness and Stiffness

Effect of Maleic Anhydride Copolymerization Mode on the Properties of PA6/ABS Blends

In Situ Formation of the Core–Shell Particles and Their Function in Toughening PA6/SEBS-g-MA/PP Blends

Maleic Anhydride-Grafted Isotactic Polybutene-1 and Modified Polyamide 6

Toughening Behavior and Morphology Study of PA6/thermal Liquid Crystalline Polyamide Blends

Polyamide-6/montmorillonite Nanocomposites Toughened with ABS-g-MA Core-Shell Structural Particles

Toughening of PA6 Nanocomposites by Reactive Acrylonitrile–butadiene–styrene Core–shell Rubber Particles

Morphology and mechanical properties of Acrylonitrile-styrene-acrylate toughened plastics with block copolymer chain structure: Acrylonitrile-styrene-acrylate (ASA) toughened plastics with block copolymer chain structure

The Preparation of Mah/St Multi-Monomer Melt Grafting on Abs and Its Compatibilizer Effect on Pa6/Abs Blends

Study on the Structure and Properties of PA6/POE-g-MAH Blends

STUDY ON TOUGHENING OF PA6/POE-g-MAH/NANO BaSO_4 BLENDS

Toughness enhancement of polyamide 6,12 with intermolecular hydrogen bonding with 3‐pentadecylphenol

Polylactide Toughening with Epoxy‐functionalized Grafted Acrylonitrile–butadiene–styrene Particles

Thermal and Mechanical Properties of Polylactide Toughened with A Butyl Acrylate-Ethyl Acrylate-Glycidyl Methacrylate Copolymer