Abstract:Preparation process of core‐shell structure ABS core‐shell impact modifier based on agglomerate technologies. Particle size distribution and the compatibility of core‐shell impact modifiers play a crucial role in determining the mechanical properties of the resin. This study presents the synthesis of a core‐shell impact modifier, a copolymer of polybutadiene grafted with styrene and acrylonitrile (PBL‐g‐SAN), using emulsion polymerization to enhance the mechanical properties of SAN resin. Polymer agglomeration technologies were employed to increase the particle size of polybutadiene latex, resulting in particles approximately 300 nm in diameter. Moreover, the effects of core‐shell modifiers with different constitutions on the mechanical properties of ABS resin were investigated. By optimizing the grafting polymerization process, improvements in impact strength of ABS resin were observed. When the St/AN ratio of the core‐shell modifier is 75/25, with a core‐shell ratio of 60/40 and MMA content at 2.5%, the impact strength of ABS resin reaches its peak while maintaining high tensile strength. The incorporation of methyl methacrylate improved the dispersion of core‐shell modifiers in SAN resin. Compared to commercial ABS resins with the same SAN and rubber content, the modified resin demonstrated a nearly 20% improvement in impact performance, and significant reductions in both production time and costs due to the polymer agglomeration method. Highlights The 300 nm polybutadiene latex was synthesized by polymer agglomeration technology. The relationship between the composition of these core‐shell modifiers and the mechanical properties of ABS resin was explored. The ABS resin with impact strength exceeding 20% of commercial material is prepared.

Toughening of PA6 Nanocomposites by Reactive Acrylonitrile–butadiene–styrene Core–shell Rubber Particles

Effect of Reactive Group Types on the Properties of Core-Shell Modifiers Toughened PA6

Polyamide-6/montmorillonite Nanocomposites Toughened with ABS-g-MA Core-Shell Structural Particles

Effect of Mixing Sequence on Phase Morphology and Mechanical Properties in Polyamide 6/butadiene (core) Styrene Acrylonitrile-G-Maleic Anhydride (shell) Latex/Organoclay Ternary Nanocomposites

Effect of ABS types on the morphology and mechanical properties of PA6/ABS blends by in situ reactive extrusion

In Situ Formation of the Core–Shell Particles and Their Function in Toughening PA6/SEBS-g-MA/PP Blends

Relationship between structure and properties in high-performance PA6/SEBS-g-MA/(PPO/PS) blends: The role of PPO and PS

Construction of Core‐Shell Structure in PA6/ABS/SEBS Blends for Achieving Stiffness‐Toughness Balance

Influence of Core-Shell Particles Structure on the Morphology and Brittle-Ductile Transition of Pbt/Abs-G-Gma Blends

Research on effect of ABS,MAH,DCP on property of PA6/ABS blend

Preparation of PBT/POE‐g‐GMA/PP Ternary Blends with Good Rigidity–toughness Balance by Core–shell Particles

Compatibilizing and toughening of the styrene and acrylonitrile copolymer and core‐shell impact modifier obtained by agglomerate technologies

Toughening Effects of "Core-Shell" Particles in PA6/SEBS-g-MA/PPO Blends

Core-Shell Particles Of Poly(Methyl Methacrylate)-Block-Poly(N-Butyl Acrylate) Synthesized Via Reversible Addition-Fragmentation Chain-Transfer Emulsion Polymerization And The Polymer'S Application In Toughening Polycarbonate

Effect of Interface on Brittle - Ductile Transition and Fracture Behavior of ABS/PA6 Blends

Toughening of PA6 with MAH Functionalized Acrylate-styrene-acrylonitrile Copolymer

Effect of Core-Shell Particles Dispersed Morphology on the Toughening Behavior of PBT/PC Blends

Toughening Of Polyamide-6 With A Maleic Anhydride Functionalized Acrylonitrile-Styrene-Butyl Acrylate Copolymer

Effect of Maleic Anhydride Copolymerization Mode on the Properties of PA6/ABS Blends

Modification of the Grafting Character to Prepare PA6/ABS-g-MA Blends with Higher Toughness and Stiffness

The Effect of Core–Shell Ratio of Acrylic Impact Modifier on Toughening PLA