Abstract:The plasticized starch exhibits flexible properties, similar to that of elastomer. In this paper, thermoplastic starch acetate (TPAS) and maleic anhydride grafted poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS‐MAH) were used to toughen polypropylene (PP) through melt blending. It is found TPAS and SEBS‐MAH have a synergistic toughening effect on PP, especially the notched impact strength of PP/TPAS/SEBS‐MAH (70/15/15) blend is as high as 83.4 kJ/m2, but only 7.2 kJ/m2 of that for PP/TPAS/SEBS (70/15/15) blend. The structure‐property relationship of the PP/TPAS/SEBS‐MAH blends was investigated. Compared with PP/TPAS/SEBS (70/15/15) blend, the TPAS domains are dispersed homogeneously in the PP/TPAS/SEBS‐MAH (70/15/15) blend with the domain size of TPAS less than 0.2 μm. The incorporation of SEBS‐MAH not only improves the compatibility between PP and TPAS but also facilitates the formation of a core‐shell structure with TPAS as the core and SEBS‐MAH as the shell. Thus formed core‐shell particles play an important role in toughening PP. The spreading coefficient of the multiphase blend reveals that only when the SEBS‐MAH content is higher than TPAS, the core‐shell structure can be formed. Otherwise, TPAS and SEBS‐MAH will disperse separately and the toughness will not be improved. This work provides a new insight into polymer toughening with TPAS. In the case of PP/TPAS/SEBS blends, SEBS and TPAS dispersed separately. For PP/TPAS/SEBS‐MAH blends, the size of TPAS was lower than that of TPAS in the PP/TPAS/SEBS blends at a given content. It indicates the compatibility between PP and TPAS was improved significantly due to the presence of SEBS‐MAH. Only when the content of SEBS‐MAH is not less than TPAS, a core‐shell structure with TPAS as the core and SEBS‐MAH as the shell can be formed, which plays an important role in PP toughening.

Relationship between structure and properties in high-performance PA6/SEBS-g-MA/(PPO/PS) blends: The role of PPO and PS

In Situ Formation of the Core–Shell Particles and Their Function in Toughening PA6/SEBS-g-MA/PP Blends

Poly(L-Lactide) Materials with Balanced Mechanical Properties Prepared by Blending with Peg-Mb-Ppa Multiblock Copolymers

Toughening Effects of "Core-Shell" Particles in PA6/SEBS-g-MA/PPO Blends

Preparation of PBT/POE‐g‐GMA/PP Ternary Blends with Good Rigidity–toughness Balance by Core–shell Particles

Construction of Core‐Shell Structure in PA6/ABS/SEBS Blends for Achieving Stiffness‐Toughness Balance

Correlation of Morphology Evolution with Superior Mechanical Properties in PA6/PS/PP/SEBS Blends Compatibilized by Multi-phase Compatibilizers

Influences of component ratio of minor phases and charge sequence on the morphology and mechanical properties of PP/PS/PA6 ternary blends

Fabrication and toughening mechanism of high toughness PP/SEBS/HDPE blends with core‐shell particles

Microstructures and Mechanical Properties of Polypropylene/polyamide 6/Polyethelene-Octene Elastomer Blends

Toughening of PBT by POE/POE-g-GMA Elastomer Through Regulating Interfacial Adhesion and Toughening Mechanism

Synergistic toughening of polypropylene by thermoplastic starch acetate and SEBS‐MAH

Preparation of Poly(Phenylene Oxide)/Polyamide-6 Nanocomposites with High Tensile Strength and Excellent Impact Performance

Super Tough PA6/PP/ABS/SEBS Blends Compatibilized by a Combination of Multi-Phase Compatibilizers

Morphology and Mechanical Properties of Polyamide 6/Polystyrene Blends Prepared by Diffusion and Subsequent Polymerization of Styrene in Polyamide 6 Pellets

Research on effect of ABS,MAH,DCP on property of PA6/ABS blend

Study on the Structure and Properties of PA6/POE-g-MAH Blends

Study on the Microstructures and Mechanical Behaviour of Compatibilized Polypropylene/Polyamide-6 Blends

Mechanism and properties of Super-Toughened ternary blends with unique 'Tassel-Bundle' morphology

Influence of the structure of sub‐micrometer core‐shell rubber particles and matrix composition on the mechanical properties, morphological structure and deformation mechanism of rubber‐modified polyphenylene oxide/polystyrene blends

Effect of Core-Shell Particles Dispersed Morphology on the Toughening Behavior of PBT/PC Blends