Abstract:Multi-phase compatibilizers are potentially attractive, not only for the preparation of ternary or multi-phase immiscible polymer blends with high performance, but also for recycling and reuse of waste plastics mixture. In this study, the maleic anhydride (MAH) and styrene (St) dual monomers grafted PP, PP-g-(MAH-co-St) is prepared as a multi-phase compatibilizer, which exhibits highly effective compatibility on the PP/PA6/SEBS (70/15/15) ternary blends. Scanning electron microscopy (SEM) reveals that, with increasing the compatibilizer, the morphology evolves from the individual PA6 particle encapsulated by SEBS to several smaller-size PA6 particles partially encapsulated by SEBS phase, then to the tiny PA6 particles and some larger-size SEBS agglomerates predominantly dispersed separately in PP matrix. The morphology development predicted by spreading coefficients shows a consummate consistency with that observed by SEM. Moreover, the good compatibilization and corresponding morphologies result in superior enhancement of mechanical properties. Compared to the uncompatibilized blend, adding 15 wt multi-phase compatibilizer to the blend leads to the best mechanical properties with the yield stress, stress at break, strain at break and impact failure energy improved significantly by 23%, 132%, 647% and 220%, respectively. The results verify that the domains with small-size PA6 particles (03-0.4 mu m) partially encapsulated by SEBS (0.5-0.7 mu m) in PP matrix are very effective to enhance the mechanical properties of the blends. The morphologies of large-size PA6 particles encapsulated by SEBS or tiny PA6 particles and some larger-size SEBS agglomerates dispersed separately in PP matrix for the enhancement in mechanical properties of the blends are very limited. Consequently, the enhanced interfacial interactions and the morphology with the rigid particles partially encapsulated by a rubber-like phase in matrix are crucial for the ternary polymer.blends. (C) 2016 Elsevier Ltd. All rights reserved.

Correlation of Morphology Evolution with Superior Mechanical Properties in PA6/PS/PP/SEBS Blends Compatibilized by Multi-phase Compatibilizers

Compatibilizing Efficiency of Copolymer Precursors for Immiscible Polymer Blends

Morphology Development and Superior Mechanical Properties of Pp/Pa6/Sebs Ternary Blends Compatibilized by Using A Highly Efficient Multi-Phase Compatibilizer

Synergetic Effect of a Reactive Compatibilizer and Organo-montmorillonite on the Dispersion of Polyamide 6 /Polydimethylsilicone Blend with a High Viscosity Ratio

Relationship between structure and properties in high-performance PA6/SEBS-g-MA/(PPO/PS) blends: The role of PPO and PS

Super Tough PA6/PP/ABS/SEBS Blends Compatibilized by a Combination of Multi-Phase Compatibilizers

Structure-property Relationships of Reactively Compatibilized PHB/EVA/starch Blends.

Influences of component ratio of minor phases and charge sequence on the morphology and mechanical properties of PP/PS/PA6 ternary blends

Creating Super-Tough and Strong PA6/ABS Blends Using Multi-Phase Compatibilizers

Compatibilization and morphology development of immiscible ternary polymer blends

High-strength and super-tough PA6/PS/PP/SEBS quaternary blends compatibilized by using a highly effective multi-phase compatibilizer: Toward efficient recycling of waste plastics

Study on the Microstructures and Mechanical Behaviour of Compatibilized Polypropylene/Polyamide-6 Blends

In Situ Formation of the Core–Shell Particles and Their Function in Toughening PA6/SEBS-g-MA/PP Blends

Preparation of PBT/POE‐g‐GMA/PP Ternary Blends with Good Rigidity–toughness Balance by Core–shell Particles

Compatibilization And Toughening Of Immiscible Ternary Blends Of Polyamide 6, Polypropylene (Or A Propylene-Ethylene Copolymer), And Polystyrene

The Effect of Functionalized SEBS on the Properties of PP/SEBS Blends

Novel Strategy for Ternary Polymer Blend Compatibilization

Research on effect of ABS,MAH,DCP on property of PA6/ABS blend

Joint Effect of Compatibilizer and Organo-Montmorillonite on Compatibilization of Polyamide-6/Poly(Phenylene Oxide) Blend: Morphology and Properties

Morphology, thermal behavior, and mechanical properties of nylon6/multi-monomer grafted polypropylene blends

Compatibilization Effect of PP-g-(MAH/VAc) on Polypropylene/Polyamide 6 Blends