Abstract:Multi-phase compatibilizers are potentially attractive, not only for the preparation of ternary or multi-phase immiscible polymer blends with high performance, but also for recycling and reuse of waste plastics mixture. In this study, the maleic anhydride (MAH) and styrene (St) dual monomers grafted PP, PP-g-(MAH-co-St) is prepared as a multi-phase compatibilizer, which exhibits highly effective compatibility on the PP/PA6/SEBS (70/15/15) ternary blends. Scanning electron microscopy (SEM) reveals that, with increasing the compatibilizer, the morphology evolves from the individual PA6 particle encapsulated by SEBS to several smaller-size PA6 particles partially encapsulated by SEBS phase, then to the tiny PA6 particles and some larger-size SEBS agglomerates predominantly dispersed separately in PP matrix. The morphology development predicted by spreading coefficients shows a consummate consistency with that observed by SEM. Moreover, the good compatibilization and corresponding morphologies result in superior enhancement of mechanical properties. Compared to the uncompatibilized blend, adding 15 wt multi-phase compatibilizer to the blend leads to the best mechanical properties with the yield stress, stress at break, strain at break and impact failure energy improved significantly by 23%, 132%, 647% and 220%, respectively. The results verify that the domains with small-size PA6 particles (03-0.4 mu m) partially encapsulated by SEBS (0.5-0.7 mu m) in PP matrix are very effective to enhance the mechanical properties of the blends. The morphologies of large-size PA6 particles encapsulated by SEBS or tiny PA6 particles and some larger-size SEBS agglomerates dispersed separately in PP matrix for the enhancement in mechanical properties of the blends are very limited. Consequently, the enhanced interfacial interactions and the morphology with the rigid particles partially encapsulated by a rubber-like phase in matrix are crucial for the ternary polymer.blends. (C) 2016 Elsevier Ltd. All rights reserved.

Morphology, thermal behavior, and mechanical properties of nylon6/multi-monomer grafted polypropylene blends

A Dissipative Particle Dynamics Study on the Compatibilizing Process of Immiscible Polymer Blends with Graft Copolymers

Combination of double-modified clay and polypropylene-graft-maleic anhydride for the simultaneously improved thermal and mechanical properties of polypropylene

CRYSTALLIZATION BEHAVIORS OF GLYCIDYL METHACRYLATE/STYRENE MULTI-MONOMER GRAFTED POLYPROPYLENE AND POLYAMIDE 6 BLENDS

Effect of Addition of Pp-G- (Gma-Co-st) on Morphologies and Properties of Pbt/Pp Blends

THE STUDY OF APPLIED BEHAVIOR OF PP/PA6 BY USING GRAFTED POLYPROPYLENE AS COMPATILIZER

Functionalization of Polypropylene and Compatibilization of Polypropylene/Nylon 6 Blends with Copolymers Containing Alpha-Methyl Styrene Units

Study of multi-monomer melt-grafting onto polypropylene in an extruder

Microphase separation structure formed in GMA/St multi-monomer melt grafted polypropylene

The Preparation of Mah/St Multi-Monomer Melt Grafting on Abs and Its Compatibilizer Effect on Pa6/Abs Blends

Effect of Different Comonomers Added to Graft Copolymers on the Properties of PLA/PPC/PLA-g-GMA Blends

Study of Melt Free Radical Grafting of Maleic Anhydride and Styrene Onto Polypropylene and Its Properties

Study on the Microstructures and Mechanical Behaviour of Compatibilized Polypropylene/Polyamide-6 Blends

FUNCTIONALIZATION OF POLYPROPYLENE AND COMPATIBILIZATION OF POLYPROPYLENE/NYLON 6 BLENDS WITH Α-Methyl STYRENE/STYRENE/MALEIC ANHYDRIDE TERNARY COPOLYMER

Morphology Development and Superior Mechanical Properties of Pp/Pa6/Sebs Ternary Blends Compatibilized by Using A Highly Efficient Multi-Phase Compatibilizer

Influences of component ratio of minor phases and charge sequence on the morphology and mechanical properties of PP/PS/PA6 ternary blends

Correlation of Morphology Evolution with Superior Mechanical Properties in PA6/PS/PP/SEBS Blends Compatibilized by Multi-phase Compatibilizers

Preparation of PBT/POE‐g‐GMA/PP Ternary Blends with Good Rigidity–toughness Balance by Core–shell Particles

Morphology and Mechanical Properties of Nylon 6/PBT Blends Compatibilized with Styrene/Maleic Anhydride Copolymer

Compatibilization and morphology development of immiscible ternary polymer blends

Compatibilization And Toughening Of Immiscible Ternary Blends Of Polyamide 6, Polypropylene (Or A Propylene-Ethylene Copolymer), And Polystyrene