Abstract:Blending type of ABS with different polybutadiene rubber (PB) and polyacrylonitrile (AN) contents in SAN phase is prepared at 240 degrees C to study the effects of PB and AN content on the structure and the properties of DB/ABS blends. Different kinds of productive ABS along with the blend-type ABS are used to compare the properties of PC/ABS and DB/ABS blends comprehensively. All blends are made by melt blending for 10 min with sheer rate of 30 r/min. The result shows that, in DB/Blend-type ABS (70/30) blends, PB content exhibits significant influence on the tensile properties. Samples with 6.3 wt% of PB always show the best performance both in yield strength and elongation at break when AN content is fixed at 18 wt%, 25 wt% and 30 wt%; while increasing AN content in the sample with the same PB content would result in better blends properties even not so obvious as PB content. Scanning electron microscopy gives exactly the same trend for phase morphology with PB and AN contents, revealing best uniform scale of dispersed phase (ABS) among 0.5 - 1.2 mu m at 6.3 wt% of PB. Thermal gravimetric analysis shows that all DB/ABS blends have good thermal stability, which is not obviously affected by PB content and AN content. Single peak of glass transition shows good compatibility in the DB/ABS blends. Excellent compatibility of DB with ABS in the sample is exhibited through dynamic mechanical analysis. The glasstransition temperature of DB/ABS blends are closed to that of DB, mildly affected by PB and AN content. Besides, both blending type ABS and different kinds of productive type ABS are used to compare the properties of DB/ABS blends and traditional bisphenol-A-type PC/ABS blends. Basic laws of tensile properties in DB/ABS remain the same as in PC/ABS blends using different types of ABS.

Morphology and Mechanical Behaviors of Rigid Organic Particles Reinforced Polycarbonate

Morphology and mechanical properties of Acrylonitrile-styrene-acrylate toughened plastics with block copolymer chain structure: Acrylonitrile-styrene-acrylate (ASA) toughened plastics with block copolymer chain structure

Core-Shell Particles Of Poly(Methyl Methacrylate)-Block-Poly(N-Butyl Acrylate) Synthesized Via Reversible Addition-Fragmentation Chain-Transfer Emulsion Polymerization And The Polymer'S Application In Toughening Polycarbonate

Polyamide 66/poly(2,6-dimethyl-1,4-phenylene oxide) compatibilization with styrene–acrylonitrile–glycidyl methacrylate: rheology, morphology, and mechanical properties

Compatibilizing and toughening of the styrene and acrylonitrile copolymer and core‐shell impact modifier obtained by agglomerate technologies

Relationship between structure and properties in high-performance PA6/SEBS-g-MA/(PPO/PS) blends: The role of PPO and PS

Mechanical and Morphological Properties and Deformation Mechanisms of Acrylonitrile-Butadiene-Styrene/Poly(ϵ-Caprolactone) Blends with Varied Matrix Composition

Blending ABS resin and its effect on structure and properties of PC/ABS BLEND alloy

Toughening Effect of Poly(Ethene-Co-1-Butene)-Graft-Methyl Methacrylate and Acrylonitrile on Styrene-Acrylonitrile Copolymer (San)

Morphology and Mechanical Properties of Nylon 6/PBT Blends Compatibilized with Styrene/Maleic Anhydride Copolymer

Effect of Styrene–acrylonitrile on the Electrical Resistivity of Polycarbonate/multiwalled Carbon Nanotube Composites

Effect of Core-Shell Particles Dispersed Morphology on the Toughening Behavior of PBT/PC Blends

Acrylonitrile-Styrene-Acrylate Particles with Different Microstructure for Improving the Toughness of Poly(styrene-co-acrylonitrile) Resin

Structure and Properties of Isosorbide type Polycarbonate/ABS Blend

Investigation of Toughening Mechanisms in Elastomeric Polycarbonate Blends through Morphological and Mechanical Characterization at Small and Medium Strain Rates

Properties of Poly(butylene Terephthalate)/bisphenol A Polycarbonate Blends Toughening with Epoxy-Functionalized Acrylonitrile–Butadiene–Styrene Particles

MORPHOLOGY AND MECHANICAL PROPERTIES OF NYLON-6/ABS POLYMER BLENDS COMPATIBILIZED BY STYRENE-MALEIC ANHYDIDE COPOLYMER

Miscibility and Morphology of AB/C‐type Blends Composed of Block Copolymer and Homopolymer or Random Coploymer, 2. Blends with Random Copolymer Effect

Effect of Poly(styrene-ran-methyl acrylate) Inclusion on the Compatibility of Polylactide/Polystyrene-b-Polybutadiene-b-Polystyrene Blends Characterized by Morphological, Thermal, Rheological, and Mechanical Measurements

Effect of polybutadiene grafted methyl methacrylate copolymer on the mechanical performance of PC/ABS composites

Recycled Polycarbonate/acrylonitrile–butadiene–styrene Reinforced and Toughened Through Chemical Compatibilization