Abstract:The primary mirror of very large submillimeter-wave telescopes will necessarily be segmented into many separate mirror panels. These panels must be continuously co-phased to keep the telescope wavefront error less than a small fraction of a wavelength, to ten microns RMS (root mean square) or less. This performance must be maintained continuously across the full aperture of the telescope, in all pointing conditions, and in a variable thermal environment. A wavefront compensation segmented mirror sensing and control system, consisting of optical edge sensors, Wavefront Compensation Estimator/Controller Soft ware, and segment position actuators is proposed. Optical edge sensors are placed two per each segment-to-segment edge to continuously measure changes in segment state. Segment position actuators (three per segment) are used to move the panels. A computer control system uses the edge sensor measurements to estimate the state of all of the segments and to predict the wavefront error; segment actuator commands are computed that minimize the wavefront error. Translational or rotational motions of one segment relative to the other cause lateral displacement of the light beam, which is measured by the imaging sensor. For high accuracy, the collimator uses a shaped mask, such as one or more slits, so that the light beam forms a pattern on the sensor that permits sensing accuracy of better than 0.1 micron in two axes: in the z or local surface normal direction, and in the y direction parallel to the mirror surface and perpendicular to the beam direction. Using a co-aligned pair of sensors, with the location of the detector and collimated light source interchanged, four degrees of freedom can be sensed: transverse x and y displacements, as well as two bending angles (pitch and yaw). In this approach, each optical edge sensor head has a collimator and an imager, placing one sensor head on each side of a segment gap, with two parallel light beams crossing the gap. Two sets of optical edge sensors are used per segment-to-segment edge, separated by a finite distance along the segment edge, for four optical heads, each with an imager and a collimator. By orienting the beam direction of one edge sensor pair to be +45 away from the segment edge direction, and the other sensor pair to be oriented -45 away from the segment edge direction, all six degrees of freedom of relative motion between the segments can be measured with some redundancy. The software resides in a computer that receives each of the optical edge sensor signals, as well as telescope pointing commands. It feeds back the edge sensor signals to keep the primary mirror figure within specification. It uses a feed-forward control to compensate for global effects such as decollimation of the primary and secondary mirrors due to gravity sag as the telescope pointing changes to track science objects. Three segment position actuators will be provided per segment to enable controlled motions in the piston, tip, and tilt degrees of freedom. These actuators are driven by the software, providing the optical changes needed to keep the telescope phased.

Alignment of the Secondary Mirror of a Space Telescope Based on Holographic Modal Wavefront Sensor

Computer Aided Alignment of 20X Schwarzschild Projection Optics

Principle and application of holographic modal wavefront sensor for extended objects and general aberration modes

Simulation alignment of optical system for space gravitational wave telescope

Modified Wavefront Sensing and Correction Methodology for Active Segment Mirror of Large Space Telescope

Mirror-mode sensing with a holographic modal wavefront sensor

Optical alignment technology for 1-meter accurate infrared magnetic system telescope

Telescope Alignment Method Using a Modified Stochastic Parallel Gradient Descent Algorithm

Analysis of active optics correction for a large honeycomb mirror

Wavefront Sensing and Control with the Many Headed Hydra Modal Basis

Low Spatio-temporal Frequency Wavefront Aberration Correction Method Based on a Movable Secondary Mirror

Hybrid Ball-Hinged Secondary Mirror Assembly for High-Precision Surface Shape Maintenance.

Mirror actively deformed and regulated for applications in space: design and performance

A Demonstration of Wavefront Sensing and Mirror Phasing from the Image Domain

An Alignment of Primary and Secondary Mirrors for Optical System in Large Telescopic

Alignment of three mirror anastigmat telescopes using a multilayered stochastic parallel gradient descent algorithm

Integrated modeling of wavefront sensing and control for space telescopes utilizing active and adaptive optics

Wavefront Compensation Segmented Mirror Sensing and Control

Efficient Wavefront Sensing for Space-Based Adaptive Optics

Method for detection of primary mirror figure deformation in space

Analyzing Misalignment Tolerances for Implicit Electric Field Conjugation