Abstract:The primary mirror of very large submillimeter-wave telescopes will necessarily be segmented into many separate mirror panels. These panels must be continuously co-phased to keep the telescope wavefront error less than a small fraction of a wavelength, to ten microns RMS (root mean square) or less. This performance must be maintained continuously across the full aperture of the telescope, in all pointing conditions, and in a variable thermal environment. A wavefront compensation segmented mirror sensing and control system, consisting of optical edge sensors, Wavefront Compensation Estimator/Controller Soft ware, and segment position actuators is proposed. Optical edge sensors are placed two per each segment-to-segment edge to continuously measure changes in segment state. Segment position actuators (three per segment) are used to move the panels. A computer control system uses the edge sensor measurements to estimate the state of all of the segments and to predict the wavefront error; segment actuator commands are computed that minimize the wavefront error. Translational or rotational motions of one segment relative to the other cause lateral displacement of the light beam, which is measured by the imaging sensor. For high accuracy, the collimator uses a shaped mask, such as one or more slits, so that the light beam forms a pattern on the sensor that permits sensing accuracy of better than 0.1 micron in two axes: in the z or local surface normal direction, and in the y direction parallel to the mirror surface and perpendicular to the beam direction. Using a co-aligned pair of sensors, with the location of the detector and collimated light source interchanged, four degrees of freedom can be sensed: transverse x and y displacements, as well as two bending angles (pitch and yaw). In this approach, each optical edge sensor head has a collimator and an imager, placing one sensor head on each side of a segment gap, with two parallel light beams crossing the gap. Two sets of optical edge sensors are used per segment-to-segment edge, separated by a finite distance along the segment edge, for four optical heads, each with an imager and a collimator. By orienting the beam direction of one edge sensor pair to be +45 away from the segment edge direction, and the other sensor pair to be oriented -45 away from the segment edge direction, all six degrees of freedom of relative motion between the segments can be measured with some redundancy. The software resides in a computer that receives each of the optical edge sensor signals, as well as telescope pointing commands. It feeds back the edge sensor signals to keep the primary mirror figure within specification. It uses a feed-forward control to compensate for global effects such as decollimation of the primary and secondary mirrors due to gravity sag as the telescope pointing changes to track science objects. Three segment position actuators will be provided per segment to enable controlled motions in the piston, tip, and tilt degrees of freedom. These actuators are driven by the software, providing the optical changes needed to keep the telescope phased.

Mirror-mode sensing with a holographic modal wavefront sensor

Methods for the Characterization of Deformable Membrane Mirrors

Research of an Adaptive Micro-Mirror Based on Micro-Opto-Electro-Mechanical- System

Wavefront Sensing and Control with the Many Headed Hydra Modal Basis

A Demonstration of Wavefront Sensing and Mirror Phasing from the Image Domain

Characterising a Holographic Modal Phase Mask for the Detection of Ocular Aberrations

Deformable mirror resolution-matching-based two-stage wavefront sensorless adaptive optics method

Principle and application of holographic modal wavefront sensor for extended objects and general aberration modes

Analysis of A Compliant Static Deformable Mirror for Wavefront Error Cancellation

Membrane based Deformable Mirror: Intrinsic aberrations and alignment issues

Close-loop Performance of a High Precision Deflectometry Controlled Deformable Mirror (DCDM) Unit for Wavefront Correction in Adaptive Optics System

Fast single pixel modal wavefront sensing using neural networks

Real-time machine-learning-driven control system of a deformable mirror for achieving aberration-free X-ray wavefronts

Mode-Voltage Constrained Control for Adaptive Optics System

Adaptive System for Ocular Wavefront Analysis With Subjective Refinement

A Support Structure for A Compliant Deformable Mirror

Compliant deformable mirror approach for wavefront improvement

Wavefront Compensation Segmented Mirror Sensing and Control

Keck Primary Mirror Closed-loop Segment Control Using a Vector-Zernike Wavefront Sensor

Development of an ELT XAO testbed using a Mach-Zehnder wavefront sensor: calibration of the deformable mirror