Abstract:The primary mirror of very large submillimeter-wave telescopes will necessarily be segmented into many separate mirror panels. These panels must be continuously co-phased to keep the telescope wavefront error less than a small fraction of a wavelength, to ten microns RMS (root mean square) or less. This performance must be maintained continuously across the full aperture of the telescope, in all pointing conditions, and in a variable thermal environment. A wavefront compensation segmented mirror sensing and control system, consisting of optical edge sensors, Wavefront Compensation Estimator/Controller Soft ware, and segment position actuators is proposed. Optical edge sensors are placed two per each segment-to-segment edge to continuously measure changes in segment state. Segment position actuators (three per segment) are used to move the panels. A computer control system uses the edge sensor measurements to estimate the state of all of the segments and to predict the wavefront error; segment actuator commands are computed that minimize the wavefront error. Translational or rotational motions of one segment relative to the other cause lateral displacement of the light beam, which is measured by the imaging sensor. For high accuracy, the collimator uses a shaped mask, such as one or more slits, so that the light beam forms a pattern on the sensor that permits sensing accuracy of better than 0.1 micron in two axes: in the z or local surface normal direction, and in the y direction parallel to the mirror surface and perpendicular to the beam direction. Using a co-aligned pair of sensors, with the location of the detector and collimated light source interchanged, four degrees of freedom can be sensed: transverse x and y displacements, as well as two bending angles (pitch and yaw). In this approach, each optical edge sensor head has a collimator and an imager, placing one sensor head on each side of a segment gap, with two parallel light beams crossing the gap. Two sets of optical edge sensors are used per segment-to-segment edge, separated by a finite distance along the segment edge, for four optical heads, each with an imager and a collimator. By orienting the beam direction of one edge sensor pair to be +45 away from the segment edge direction, and the other sensor pair to be oriented -45 away from the segment edge direction, all six degrees of freedom of relative motion between the segments can be measured with some redundancy. The software resides in a computer that receives each of the optical edge sensor signals, as well as telescope pointing commands. It feeds back the edge sensor signals to keep the primary mirror figure within specification. It uses a feed-forward control to compensate for global effects such as decollimation of the primary and secondary mirrors due to gravity sag as the telescope pointing changes to track science objects. Three segment position actuators will be provided per segment to enable controlled motions in the piston, tip, and tilt degrees of freedom. These actuators are driven by the software, providing the optical changes needed to keep the telescope phased.

Wavefront Sensing and Control with the Many Headed Hydra Modal Basis

Integrated modeling of wavefront sensing and control for space telescopes utilizing active and adaptive optics

The future looks dark: improving high contrast imaging with hyper-parameter optimization for data-driven predictive wavefront control

Efficient Wavefront Sensing for Space-Based Adaptive Optics

Identification and Adaptive Control of a High-Contrast Focal Plane Wavefront Correction System

Recent Developments of Interferometric Wavefront Sensing

Low-order wavefront control using a Zernike sensor through Lyot coronagraphs for exoplanet imaging

Mirror-mode sensing with a holographic modal wavefront sensor

Battle of the Predictive Wavefront Controls: Comparing Data and Model-Driven Predictive Control for High Contrast Imaging

A Demonstration of Wavefront Sensing and Mirror Phasing from the Image Domain

Dynamic Mode Decomposition for Aero-Optic Wavefront Characterization

Modern Wavefront Control for Space-Based Exoplanet Coronagraph Imaging

Tempestas ex machina: A review of machine learning methods for wavefront control

High Speed Focal Plane Wavefront Sensing with an Optical Chopper

Various Wavefront Sensing and Control Developments on the Santa Cruz Extreme AO Laboratory (SEAL) Testbed

Experimental Trials With The Optical Differentiation Wavefront Sensor For Extended Objects

Focus diverse phase retrieval testbed development of continuous wavefront sensing for space telescope applications

Joint optimization of wavefront sensing and reconstruction with automatic differentiation

Deformable mirror-based pupil chopping for exoplanet imaging and adaptive optics

Wavefront Compensation Segmented Mirror Sensing and Control

Improved high-contrast wavefront controllers for exoplanet coronagraphic imaging systems