Abstract:Cryogenic deformation had been proved to promote the strength and toughness in several kinds of alloys. The microstructure responses and mechanical properties of cryogenic rolling 2195 Al–Cu–Li alloy after heat treatment were investigated systematically in this study. The annealed 2195 Al–Cu–Li alloy plates were subjected to cryogenic rolling to a reduction of 80% at −190 °C, followed by the solid solution at 540 °C for 2 h and aging treatment at 175 °C for different durations. Both the tensile strength and ductility of heat-treated specimen increased compared with the as-rolled sample, while the yield strength of the cryogenic rolling sample was higher anomaly. In addition, the tensile strength, yield strength, and elongation of the heat-treated samples increased firstly and then decreased with the increase of aging time. The number of T1 phases was initially increased with the aging time extended to 12 h and decreased after the aging duration was increased to 16 h. While the number of θ' gradually decreases with aging time increased. Based on the precipitation kinetics, aging kinetics, and dislocation theory, a physically based model considering the variation of dislocation density and volume fraction of the T1 phase and aging duration was established in this paper, which is in good agreement with the experimental data. Meanwhile, a strong connection between the dislocation density and fraction of the T1 phase and aging duration is established.

Effect of Cryorolling on Microstructure, Conductivities, and Mechanical Properties of a Cast Near-Eutectic Al-Si-Fe-Mg Alloy

High Strength and High Electrical Conductivity CuMg Alloy Prepared by Cryorolling

Recrystallization Behavior and Mechanical Properties of Az31b Alloy During the Hot-Rolling Process

Mechanical property enhancement and microstructure evolution of an Al-Cu-Li alloy via rolling at different temperatures

Microstructure evolution and mechanical properties of Al−3.6Cu−1Li alloy via cryorolling and aging

Microstructure Evolution, Thermal Conductivity and Mechanical Properties of Hot-Rolling Al–Si–Fe–Mg Alloy under Different Reductions

Work Hardening Behavior and Microstructure Evolution of a Cu-Ti-Cr-Mg Alloy during Room Temperature and Cryogenic Rolling

Effect of cryogenic rolling and multistage thermo-mechanical treatment on the microstructure and properties of the Cu-0.4Cr-0.39Zn-0.1Mg-0.07Zr alloy

Microstructure evolution, mechanical response, and corrosion resistance for a 2195 Al-Li alloy under different rolling reductions during cryorolling

Effect of Cold Rolling and Cryogenic Treatment on the Microstructure and Mechanical Properties of Fe–32Ni Alloy

Effects of cryogenic treatment on microstructure and mechanical properties of AZ31 magnesium alloy rolled at different paths

Influence of alloy chemistry on the deformation behaviour and anisotropic properties of aluminium ultra-fine-grained thin sheets

Effect of heat treatment on the microstructure and mechanical properties of cryogenic rolling 2195 Al–Cu–Li alloy

Effects of Rolling-Cryogenic Process on Microstructure and Mechanical Properties of AZ31 Magnesium Alloy Sheets

Effect of Cryorolling and Ageing on the Microstructure and Mechanical Properties of Al 7085 Alloy

Influence of Asymmetric Rolling Process and Thickness Reduction on the Microstructure and Mechanical Properties of the Al–Mg-Si Alloy

Recrystallization behavior and texture evolution during annealing of cryogenic-rolled 3003 aluminum alloy

Effect of Deep-Cooling Rolling Deformation on the Microstructure and Mechanical Properties of an Al-4.5Cu-1.5Mg-0.6Mn-0.2Ti Alloy

Effects Of Rolling Process On Microstructure And Mechanical Property Of 7050 Aluminum Alloy

Effect of cryogenic rolling on the microstructure and texture of CuCrZr alloy

Effect of Rolling Reduction on Microstructures and Mechanical Properties of Sc-Containing Al-3.2Cu-1.5Li Alloy