Abstract:Enhancing inlet gas temperature in aero/gas turbines to reduce their carbon-footprint, has led to a strive for better performing inlet cooling mechanism of the turbine blades. The internal cooling of the blades is made by ceramic cores in their casting process, but conventional ceramic molding has long reached its maximum possible geometrical complexity, hence shedding light on 3D printing of these cores. The objective of this study is to develop low-viscous, fully stabilized, commercially viable ink for vat-photopolymerization of silica-based ceramics. This paper investigates the best dispersion type and amount for different formulated monomer mixtures, and explains the best correlation between viscosity, solid loading, binders, dispersants, peeling forces and mechanical properties, and offers an optimized mixture to avoid the common ceramic printing issue, namely crack propagation of cores during sintering. Among five dispersant agents, the SOL20, SOL24 and FA4611 exhibited better performance than other dispersion agents, and the optimum concentration level for each binder and dispersant agent was ensured through sedimentation test. Their dispersion capability and long-term stability were further investigated to designate the best dispersion agent for each binder system. Further verification was made by sedimentation study of the samples at 40 °C for 40 days and reducing the superficial area of the used powder mixture. According to the result of the rheology analysis, the best dispersions were achieved using SOL20 for the loaded binder mixtures of M1 and M4, SOL24 for M3and FA4611 for M2. The instability of M1 and M2 with their respective dispersant agent was coordinated through the thixotropic agent of TX/2, and complete stabilization and near-Newtonian behavior were achieved. However, the research showed that the addition of TX/2 to fully stabilized M4 and M2 suspensions negatively impacts the mixtures' rheological behavior from near-Newtonian to shear-thickening. In the final stage of this study, peeling forces, sintering and three-point bending tests were conducted to determine the final formulated suspension to print ceramic core components. M4 and SOL20 combination was selected for SiO 2 -ZrSiO 4 loading and dispersing, respectively. The impact of solid loading between the range of 58 and 65 vol.% on the rheological behavior of the final suspension and the mechanical properties of sintered bodies were investigated to assign an optimum solid rate. The adequate strength on sintered and degree of viscosity for ceramic vat-polymerization processing was achieved at 58 vol.%. Lastly, a validation study is conducted by printing a complex ceramic core model by a commercial LCD hobby printer. This validation shows the significance of this study to scale up the manufacturing of complex-shaped ceramic cores and to revolutionize the sector, by printing inexpensive and readily available irregular-shaped (non-atomized) ceramic powder, using the most cost-effective LCD printers (non-specialized expensive ceramic printers).

Preparation of Low-Cost High Strength Soluble Ceramic Cores Using Heavy Calcium Carbonate by Binder Jetting and Vacuum Impregnation

Fabrication of high-strength and anti-hydration water-soluble calcia-based ceramic core modified with nano-ZrO2 via direct ink writing method

Water-Soluble Sand Core Made by Binder Jetting Printing with the Binder of Potassium Carbonate Solution

Optimization of the injection molding process for development of high performance calcium oxide -based ceramic cores

Influence of debinding parameter and nano-ZrO2 particles on the silica-based ceramic cores fabricated by stereolithography-based additive manufacturing

Fabrication of Silica-Based Ceramic Cores with Internal Lattice Structures by Stereolithography

Effect of sodium silicate solution combined yttrium oxide stabilized zirconia nanopowders on the properties of alumina ceramics fabricated by binder jetting additive manufacturing

Alumina-based ceramic cores prepared by vat photopolymerization and buried combustion method

Performance of a Water-Soluble Ceramic Core and Its Application in Aluminum Casting

Fused silica ceramic core based on network-structured zircon design via 3D printing

Direct ink writing additive manufacturing of porous alumina-based ceramic cores modified with nanosized MgO

Effect of sintering aid combined vacuum infiltration on the properties of Al 2 O 3 -based ceramics via binder jetting

Enhanced 3D printed Al2O3 core via in-situ mullite

Effect of Al(OH) 3 on the Properties of Silica-based Ceramic Cores Prepared by Laser Powder Bed Fusion Combined with Vacuum Infiltration

Achieving high-strength, high-porosity and relatively low-shrinkage in extrusion-based 3D printed ZrO 2 ceramics by adjusting CaCO 3 addition and sintering temperature

Binder stabilization and rheology optimization for vat-photopolymerization 3D printing of silica-based ceramic mixtures

3D Printing of Porous Si2N2O Ceramics Based on Strengthened Green Bodies Fabricated Via Strong Colloidal Gel

Preparation of high-performance silica-based ceramic cores with B4C addition using selective laser sintering and SiO2–Al2O3 sol infiltration

Improved mechanical properties of SiB6 reinforced silica-based ceramic cores fabricated by 3D stereolithography printing

Fabrication of Al2O3 ceramic cores with high porosity and high strength by vat photopolymerization 3D printing and sacrificial templating

Si3N4 Hollow Microsphere Toughened Porous Ceramics from Direct Coagulation Method Via Dispersant Reaction