Abstract:The realization of the necessary energy-efficient technological solutions for the production of highly porous SiC-ceramic materials requires appropriate research. The results of developing energy-efficient one-step methods for the synthesis of porous SiC-based ceramics and studying the characteristics of the obtained ceramics are presented. The effect of the morphology of initial powders on the synthesized product is considered. Ultrafine silicon carbide powders of two types, identical in characteristic particle size, but quite different in the surface morphology, were used as fillers in the synthesis of experimental samples of porous ceramics. The first one was obtained by the traditional furnace method (SiC f ), the second one was synthesized by the technology of self-propagating high-temperature synthesis (SiC shs ). It is shown that the particle morphology of initial powder components determines the structural parameters and characteristics of synthesized porous ceramics. The pore space parameters (average pore size, specific surface area, equivalent hydraulic diameter, permeability, etc.) can vary significantly. Porous ceramic materials synthesized on the basis of SiC f have an open porosity of 47%, high liquid permeability (up to 2 mDarcy), overwhelming dominance of α-SiC phase, and a narrow pore distribution with an average pore size of about 1 μm. High open porosity (more than 58 %), highly developed nanostructured pore space surface with an area of more than 12 m 2 /g, and wider pore size distribution (average pore size — 140 nm) are observed in porous ceramic materials based on SiC shs . The obtained results can be used to improve energy-efficient synthesis technologies and methods for predicting the properties of highly porous SiC-based ceramic materials. This will make it possible to create highly porous SiC ceramics within a priory predicted limits of effective applicability for the processes of ultrafiltration or catalysis.

Fabrication of Porous Zirconia Using Filter Paper Template

Facile Fabrication of Porous ZnO by a Template Free Method

Additive manufacturing of interconnected hierarchically porous zirconia: Utilizing both microspherical and filamentary pore-forming agents via direct ink printing

Synthesis of Monolithic Zirconia with Macroporous Bicontinuous Structure Via Epoxide-Driven Sol–gel Process Accompanied by Phase Separation

Fabrication of Porous Zirconia Ceramics by Injection Molding Method

Preparation of Porous Ceramic Support with Inorganic Filtration Membrane

Fabrication and properties of a stable and porous YSZ/nano-HA structure by binder jetting processes

Study of the effect of the morphology of initial powders on the structural and dimensional characteristics of SiC-based porous ceramic materials

In Vitro Cell Proliferation and Mechanical Behaviors Observed in Porous Zirconia Ceramics.

Fused deposition fabrication of high-quality zirconia ceramics using granular feedstock

Microstructure and permeability of porous YSZ ceramics with aligned and gradient pore channels fabricated by freeze casting

Fabrication of porous alumina–zirconia ceramics by gel-casting and infiltration methods

Porous Yttria‐stabilized Zirconia Ceramics Fabricated by Nonaqueous‐Based Gelcasting Process with PMMA Microsphere As Pore‐Forming Agent

Fabrication of Porous Ceramics by Direct Foaming

Hierarchically porous zirconium dioxide dual-templated by acacia mangium tannin extract and an amphiphilic triblock copolymer

Fabrication of Complex-Shaped Zirconia Ceramic Parts Via a DLP-stereolithography-based 3D Printing Method

Template-assisted syntheses of two novel porous zirconium methylphosphonates

Preparation and stereolithography 3D printing of ultralight and ultrastrong ZrOC porous ceramics

Optimization of the Tape Casting Slurries for High-Quality Zirconia Substrates

Fabrication and Mechanical Properties of Homogeneous Zirconia Toughened Alumina Ceramics Via Cyclic Solution Infiltration and in Situ Precipitation

Design, manufacturing and properties of controllable porosity of ceramic filters based on SLA-3D printing technology