Abstract:PURPOSE To design and fabricate zirconia bars with porous surfaces using stereolithography and evaluate their surface characteristics and flexural strengths. METHODS Five groups of zirconia bars (20 mm × 4 mm × 2 mm) with interconnected porous surfaces were designed and manufactured: (i) 400-μm pore size and 50% porosity (D400-P50 group), (ii) 400-μm pore size and 30% porosity (D400-P30 group), (iii) 200-μm pore size and 50% porosity (D200-P50 group), (iv) 200-μm pore size and 30% porosity (D200-P30 group), and (v) 100-μm pore size and 30% porosity (D100-P30 group). Zirconia bars without a porous surface (NP) were used as controls. The surface topographies and pore structures were investigated using scanning electron microscopy and three-dimensional laser microscopy. The printed porosity was calculated using the Archimedes method. Fifteen specimens from each group were subjected to a three-point bending test according to the ISO 6872:2015 standard. A Weibull analysis was performed, and the fractured surfaces were examined using scanning electron microscopy. RESULTS Zirconia bars with porous surfaces were designed and successfully manufactured. The designed pore size, porosity, and shape of the printed pores were approximately achieved for all the porous surfaces. The flexural strength of the control group was significantly higher than those of the groups with porous surfaces (p < 0.001). For the same porosity, groups with a pore size of 400 μm exhibited a lower flexural strength than the other groups (p<0.001). Additionally, for the same pore-size design, the flexural strengths of group D400-P50 and D400-P30 exhibited no significant differences (p = 0.150), while the flexural strengths of D200-P30 were significantly higher than that of D200-P50 group (p = 0.043). The control group and D400-P50 group had higher Weibull moduli than the other groups. The fractography of the specimens with porous surfaces indicated more than one crack origin, mainly owing to defects, including pores and cracks. CONCLUSION Zirconia bars with porous surfaces were successfully designed and fabricated using the stereolithography technique. Although porous surfaces may be advantageous for osteogenesis, the porous-surface design can reduce the flexural strength of the printed zirconia bars. By reducing the pore size, controlling the porosity, and improving the printing accuracy, a higher strength can be achieved. This article is protected by copyright. All rights reserved.

In Vitro Cell Proliferation and Mechanical Behaviors Observed in Porous Zirconia Ceramics.

The characteristic and osteogenic effect of a nanoporous coating of zirconia implant

Effect of Foreign Ion Substitution and Micropore Tuning in Robocasting Single-Phase Bioceramic Scaffolds on the Physicochemical Property and Vascularization

[Effect of Porous Zirconia Ceramics on Proliferation and Differentiation of Osteoblasts].

Proliferation and osteogenic response of MC3T3-E1 pre-osteoblastic cells on porous zirconia ceramics stabilized with magnesia or yttria

Preparation and Characterization of Functional Gradient Porous Zro2 Ceramics

Mechanical Performance of Polymer-Infiltrated Zirconia Ceramics.

In vitro cell proliferation evaluation of porous nano-zirconia scaffolds with different porosity for bone tissue engineering

Role and Mechanism of a Micro-/Nano-Structured Porous Zirconia Surface in Regulating the Biological Behavior of Bone Marrow Mesenchymal Stem Cells.

Preparation of Porous Spodumene/zircon Composite Ceramics and Its Thermal and Mechanical Properties

Preparation and performance of zirconium oxide-toughened hydroxyapatite nano-composite porous bioceramic

3D Printed Zirconia Ceramics Via Fused Deposit Modeling and Its Mechanical Properties

Porous alumina, zirconia and alumina/zirconia for bone repair: fabrication, mechanical and in vitro biological response

Fabrication of enamel-like structure on polymer-infiltrated zirconia ceramics

Additive manufacturing of interconnected hierarchically porous zirconia: Utilizing both microspherical and filamentary pore-forming agents via direct ink printing

The evaluation of prepared microstructure pattern by carbon-dioxide laser on zirconia-based ceramics for dental implant application: an in vitro study

Surface Characteristics and Flexural Strength of Porous-Surface Designed Zirconia Manufactured Via Stereolithography.

Microstructure, mechanical properties, friction and wear performance, and cytotoxicity of additively manufactured zirconia-toughened alumina for dental applications

Microstructure and Electrical Properties of Porous Pzt Ceramics Fabricated by Different Methods

Preparation of CePO4-coated Zirconia Ceramics and Their Mechanical Behavior

Preparation of Porous SiC Ceramics Using Starch as Pore-forming Agent