Abstract:Statement of problem: When compared with subtractive fabricating methods, additive manufacturing (AM) technologies are capable of fabricating complex geometries with different material porosities. However, the manufacturing accuracy and shrinkage of the stereolithography (SLA) AM zirconia with different porosities are unclear. Purpose: The purpose of this in vitro study was to measure the manufacturing accuracy and volumetric changes of AM zirconia specimens with porosities of 0%, 20%, and 40%. Material and methods: A digital design of a bar (25×4×3 mm) was obtained by using an open-source software program (Blender, version 2.77a; The Blender Foundation). The standard tessellation language (STL) file was exported. Three groups were created based on the material porosity: 0% porosity (0% group), 20% porosity (20% group), and 40% porosity (40% group). The STL was used to manufacture all the specimens by using an SLA ceramic printer (CeraMaker 900; 3DCeram Co) and zirconia material (3DMix ZrO2 paste; 3DCeram Co) (n=20). After manufacturing, the specimens were cleaned of the green parts by using a semiautomated cleaning station. Subsequently, debinding procedures was completed in a furnace at 600 °C. The sintering procedures varied among the groups to achieve different porosities. For the 0% group, the ZrO2 was sintered in a furnace at 1450 °C, and for the 20% and 40% groups, the sintering temperature varied between 1450 °C and 1225 °C. The specimen dimensions (length, width, and height) were measured 3 times with digital calipers, and the mean value was determined. The manufacturing volume shrinkage (%) was calculated by using the digital design of the bar and the achieved AM dimensions of the specimens. The Shapiro-Wilk test revealed that the data were not normally distributed. Therefore, the data were analyzed by using the Kruskal-Wallis followed by pairwise Mann-Whitney U tests (α=.05). Results: The Kruskal-Wallis test demonstrated significant differences among the groups in length, width, and height (P<.001). The Mann-Whitney U test indicated significant differences in pairwise comparisons of length, width, and height among the 3 groups (P<.001). The 0% group obtained a median ±interquartile range values of 20.92 ±0.14 mm in length, 3.43 ±0.07 mm in width, and 2.39 ±0.03 mm in height; the 20% group obtained 22.81 ±0.29 mm in length, 3.74 ±0.07 mm in width, and 2.62 ±0.05 mm in height; and the 40% group presented 25.11 ±0.13 mm in length, 4.14 ±0.08 mm in width, and 2.96 ±0.02 mm in height. Significant differences in manufacturing volumetric changes were encountered among the 3 groups (P<.001). In all groups, volumetric changes in the length, width, and height were not uniform, being higher in the z-axis direction compared with the x- and y-axis. The manufacturing volumetric changes varied from -20.33 ±1.00% to +3.5 ±2.00%. Conclusions: The 40%-porosity group obtained the highest manufacturing accuracy and the lowest manufacturing volume change, followed by the 20%-porosity and the 0%-porosity groups. An uneven manufacturing volume change in the x-, y-, and z-axis was observed. However, none of the groups tested were able to perfectly match the virtual design of the specimens.

Surface Characteristics and Flexural Strength of Porous-Surface Designed Zirconia Manufactured Via Stereolithography.

The Flexural Strength and Flexural Modulus of Stereolithography Additively Manufactured Zirconia with Different Porosities

The characteristic and osteogenic effect of a nanoporous coating of zirconia implant

Influence of 3D printed surface micro-structures on molding performance and dental bonding properties of zirconia

3D Printed Zirconia Ceramics Via Fused Deposit Modeling and Its Mechanical Properties

Physiomechanical and Surface Characteristics of 3D-Printed Zirconia: An In Vitro Study

Manufacturing accuracy and volumetric changes of stereolithography additively manufactured zirconia with different porosities

Additive manufacturing of interconnected hierarchically porous zirconia: Utilizing both microspherical and filamentary pore-forming agents via direct ink printing

Zirconia specimens printed by vat photopolymerization: Mechanical properties, fatigue properties, and fractography analysis

Microstructure and mechanical properties of 3D printed porous Al2O3–ZrO2 laminated ceramics with tailored porosity

Effect of printing layer orientation and polishing on the fatigue strength of 3D-printed dental zirconia

Novel laser textured surface designs for improved zirconia implants performance

Dental zirconia fabricated by stereolithography: Accuracy, translucency and mechanical properties in different build orientations

Effect of the Intaglio Surface Treatment and Thickness of Different Types of Yttria-Stabilized Tetragonal Zirconia Polycrystalline Materials on the Flexural Strength: In-Vitro Study

The effects of optimized microstructured surfaces on bond strength and durability of NPJ-printed zirconia

Effect of high-speed sintering on the microstructure, mechanical properties and ageing resistance of stereolithographic additive-manufactured zirconia

Strength and Adaptation of Stereolithography-Fabricated Zirconia Dental Crowns: an in Vitro Study

Evaluating mechanical and surface properties of zirconia-containing composites: 3D printing, subtractive, and layering techniques

Effect of different surface treatments and adhesive cementation on the surface topography and flexural strength of translucent and ultra‐translucent monolithic zirconia

A Clean, Rapid, and Controllable Approach for Establishing Bioactive Surfaces on Zirconia Implants

Microstructure and mechanical properties of 3D‐printed zirconia bone scaffold: Experimental and computational analysis