Abstract:Porous yttria‐stabilized zirconia ceramics with 6–40% porosity are fabricated using vat photopolymerization 3D printing. The porous ceramics exhibit a Weibull modulus of 5.3, a characteristic strength of over 36 MPa, and a thermal shock resistance up to 500 °C, demonstrating potential for improved efficiency and reduced fabrication costs in solid oxide fuel cells and electrolysis cells. Advances in vat photopolymerization 3D printing have the potential to significantly improve the production of ceramic materials for electrochemical energy devices. Solid oxide fuel cells (SOFCs) and solid oxide electrolysis cells (SOECs) necessitate high‐resolution ceramic manufacturing methods, as well as precisely controlled porosity (≈20–40%) for optimal gas transport. Achieving a balance between this porosity and mechanical integrity, especially under thermal stress, remains a challenge. Herein, the successful fabrication of porous yttria‐stabilized zirconia (YSZ) ceramics using vat photopolymerization 3D printing is demonstrated, achieving porosities ranging from 6% to 40% and corresponding grain sizes of ≈80–550 nm. It is found that 3D‐printed YSZ with ≈33% porosity exhibited a Weibull modulus of m = 5.3 and a characteristic strength of over 36 MPa. In the investigation, it is further revealed that these ceramics can withstand thermal shock up to 500 °C, retaining over 70% of their flexural strength. This remarkable performance suggests significant potential for 3D‐printed porous YSZ in SOFCs and SOECs, paving the way for potential improved efficiency, reduced fabrication costs, and innovative designs in these next‐generation clean energy technologies.

Preparation and stereolithography 3D printing of ultralight and ultrastrong ZrOC porous ceramics

Preparation of excellent performance ZTA ceramics and complex shaped components using digital light processing 3D printing technology

3D printing of hollow lattice structures of ZrO2(3Y)/Al2O3 ceramics by vat photopolymerization: Process optimization, microstructure evolution and mechanical properties

Properties and ceramic transformation of Si–Zr–O–C precursor ceramics with porous structure

Ultrahigh Strength of Three-Dimensional Printed Diluted Magnesium Doping Wollastonite Porous Scaffolds

POLYMER-DERIVED SIC CERAMIC WITH TRIPLY PERIOD MINIMAL SURFACE STRUCTURE FABRICATION THROUGH DIGITAL LIGHT PROCESSING

3D Printing of Hollow Microspheres into Strong Hierarchical Porous Ceramics

Fabrication of High-Performance Al2O3-ZrO2 Composite by a Novel Approach That Integrates Stereolithography-Based 3D Printing and Liquid Precursor Infiltration

Advancements in DLP 3D Printing: High Strength Alumina Toughened Zirconia Ceramics for Biomedical Applications

Highly Porous ZrO2 Cellular Ceramics with 3D Network Architecture

Fabrication of porous aluminum ceramics beyond device resolution via stereolithography 3D printing

Digital Light Processing 3D‐Printed Porous Yttria‐Stabilized Zirconia with High‐Thermal Shock Resistance

Towards high strengthening efficiency of equiaxed and platelet-shaped alumina reinforced zirconia ceramics with textured microstructure using DLP-based stereolithography

Preparation of ZTA composite ceramics derived from sol–gel method by DIW printing

3D Printed Zirconia Ceramics Via Fused Deposit Modeling and Its Mechanical Properties

Fabrication of Complex-Shaped Zirconia Ceramic Parts Via a DLP-stereolithography-based 3D Printing Method

DLP 3D printing of high strength semi-translucent zirconia ceramics with relatively low-loaded UV-curable formulations

3D printing of dense structural ceramic microcomponents with low cost: Tailoring the sintering kinetics and the microstructure evolution

Fabrication of fine and complex lattice structure Al2O3 ceramic by digital light processing 3D printing technology

Preparation of high performance dense Al 2 O 3 ceramics by digital light processing 3D printing technology

Ultrahigh-Strength Porous Ceramic Composites via a Simple Directional Solidification Process