Abstract:The construction of ceramic components with UV curing is a developing trend by an additive manufacturing (AM) technology, due to the excellent advantages of high precision selective fixation and rapid prototyping, the application of this technology to bone defect repair had become one of the hotspots of research. Hydroxyapatite (HAP) is one of the most popular calcium phosphate biomaterials, which is very close to the main ingredient of human bones. Thus, hydroxyapatite biomaterials are popular as bone graft materials. In summary, the preparation of HAP bioceramics by a 3D printing of digital light processing (DLP) is a promising work. However, the preparation of HAP hybrid suspensions with high solid loading and good fluidity that can be printed by DLP encountered some challenges. Therefore, the purpose of this work is to improve and develop a novel UV-curing suspension with a high solids loading, which the suspension with the hydrodynamic properties and stability are suitable for DLP printer, in order to compensate for the brittleness of HAP ceramics itself to a certain extent, a low amount of zirconia was added in the suspension as an additive to fabricate a zirconia toughened HAP bioceramic composite by a DLP of 3D printing. In this work, the HAP powder was pre-modified by two organic modifiers to improve the compatibility in the acrylic resin system, and the addition of the castor oil phosphate further reduced the shear stress of the suspension to ensure strong liquidity. The UV suspension with 60 wt% powder particle loading had a minimum viscosity of 7495 mPa·s at 30 rpm, which was vacuum sintered at 1100 °C, 1200 °C, and 1250 °C, respectively. The composite ceramics (with 6 wt% ZrO2) at 1200 °C had a relative density of 90.7%, while the sintered samples at 1250 °C had stronger tensile strength and bending strength. The toughening effect of zirconia incorporation on HAP ceramics was also confirmed by the change of tensile modulus and bending modulus, whereas the corresponding mechanical properties were also significantly enhanced.

Advancements in DLP 3D Printing: High Strength Alumina Toughened Zirconia Ceramics for Biomedical Applications

DLP 3D printing of high strength semi-translucent zirconia ceramics with relatively low-loaded UV-curable formulations

Preparation of excellent performance ZTA ceramics and complex shaped components using digital light processing 3D printing technology

Towards high strengthening efficiency of equiaxed and platelet-shaped alumina reinforced zirconia ceramics with textured microstructure using DLP-based stereolithography

DLP 3D printing of TiO2-doped Al2O3 bioceramics: Manufacturing, mechanical properties, and biological evaluation

Microstructural Evolution, Enhanced Mechanical Properties, and Complex Shapes Design in High Solid Content Alumina Ceramics Through Additive Manufacturing

Evaluation of zirconia ceramics fabricated through DLP 3d printing process for dental applications

UV-Curing Assisted Direct Ink Writing of Dense, Crack-Free, and High-Performance Zirconia-Based Composites With Aligned Alumina Platelets

Digital light processing‐based additive manufacturing of orientation‐controlled Al2O3 ceramics with improved damage tolerance

Fabrication and characterisation of ceramics via low-cost DLP 3D printing

Digital Light Processing of 3Y-TZP Strengthened ZrO2 Ceramics

Preparation of high performance dense Al 2 O 3 ceramics by digital light processing 3D printing technology

Hydrogel-based DLP 3D Printing of Dense Zirconia Ceramics

Digital light processing 3D printing of ceramic materials: a review on basic concept, challenges, and applications

Zirconia toughened hydroxyapatite biocomposite formed by a DLP 3D printing process for potential bone tissue engineering

Preparation and stereolithography 3D printing of ultralight and ultrastrong ZrOC porous ceramics

High-performance and high-precision Al2O3 architectures enabled by high-solid-loading, graphene-containing slurries for top-down DLP 3D printing

Preparation of large-size alumina ceramic parts by DLP 3D printing using high-solid-loading paste and optimizing the debinding process

3D printed polylactide based zirconia toughened alumina composites: fabrication, mechanical and in vitro evaluation

Microstructures and mechanical properties of additively manufactured alumina ceramics with digital light processing

DLP 3D printing of scandia-stabilized zirconia ceramics