Abstract:Producing micro and macroporous 3D structures that mimic the bone architecture of a specific anatomic region, namely the rounded trabeculae in trabecular bone, is a considerable challenge, to which additive manufacturing can make a fundamental contribution. The main objective of the work was to explore the Digital Light Processing (DLP) technique in obtaining customized parts, from a ceramic suspension composed of two different materials, specifically alumina and hydroxyapatite (HA), with a trabecular bone architecture, using Computer Assisted Design (CAD) modelling techniques and additive manufacturing. Hydroxyapatite (HA) was added to the alumina matrix to improve the biocompatibility and bioactivity of the composites after sintering. After optimizing all printing parameters and the suspensions rheological properties, samples in alumina and alumina-hydroxyapatite with the desired architecture were obtained. The influence of the incorporation of hydroxyapatite in the alumina formulations was also analyzed, with increasing hydroxyapatite contents: 5, 10, and 15 wt%. The rheological behaviour of the suspensions was studied in a plate-to-plate system. The physical-chemical and mechanical characterization of produced samples were carried out by X-ray diffraction, Scanning electron microscopy, and compressive tests. The suspensions prepared with two different materials showed adequate viscosity to achieve a good spread and homogeneous layers in the 3D printing process. In the produced samples, the occurrence of a hibonite phase (CaAl12O19), resulting from the reaction between alumina and hydroxyapatite during the sintering step, increased the compressive strength of the samples. The high temperature needed for sintering alumina led to the conversation of HA into TCP. The achieved mechanical strength results from the porosity level and the thickness of the struts of the printed architecture. DLP showed to be a precision printing technology of low cost that can be used to fabricate parts in the industry from a suspension composed of a mixture of alumina and HA powders, which is very useful in the bone repair field and not previously reported.

DLP 3D printing of TiO2-doped Al2O3 bioceramics: Manufacturing, mechanical properties, and biological evaluation

Advancements in DLP 3D Printing: High Strength Alumina Toughened Zirconia Ceramics for Biomedical Applications

POLYMER-DERIVED SIC CERAMIC WITH TRIPLY PERIOD MINIMAL SURFACE STRUCTURE FABRICATION THROUGH DIGITAL LIGHT PROCESSING

[Status of 3D Printing Technology for Preparing Bioceramic Materials]

Preparation, Microstructure, and Properties of ZrO2(3Y)/Al2O3 Bioceramics for 3D Printing of All-ceramic Dental Implants by Vat Photopolymerization

Additive manufacturing of ceramic alumina/calcium phosphate structures by DLP 3D printing

Fine lattice structural titanium dioxide ceramic produced by DLP 3D printing

Digital light processing 3D printing of ceramic materials: a review on basic concept, challenges, and applications

Ceramic 3D printing using lithium silicate prepared by sol-gel method for customizing dental prosthesis with optimal translucency

Digital light processing (DLP) of nano biphasic calcium phosphate bioceramic for making bone tissue engineering scaffolds

DLP 3D printing porous β-tricalcium phosphate scaffold by the use of acrylate/ceramic composite slurry

Titanium dioxide bioceramics prepared by 3D printing method and its structure effect on stem cell behavior

Preparation of high performance dense Al 2 O 3 ceramics by digital light processing 3D printing technology

Preparation of excellent performance ZTA ceramics and complex shaped components using digital light processing 3D printing technology

Evaluation of zirconia ceramics fabricated through DLP 3d printing process for dental applications

Digital light processing‐based additive manufacturing of orientation‐controlled Al2O3 ceramics with improved damage tolerance

Ultrahigh Strength of Three-Dimensional Printed Diluted Magnesium Doping Wollastonite Porous Scaffolds

Fabrication and characterisation of ceramics via low-cost DLP 3D printing

Stereolithography-Based Additive Manufacturing of High-Performance Osteoinductive Calcium Phosphate Ceramics by a Digital Light-Processing System

Spray‐Drying‐Assisted Digital Light Processing for Highly Dense and Precise Three‐dimensional Printed Barium Titanate Ceramic Structures

High performance hydroxyapatite ceramics and a triply periodic minimum surface structure fabricated by digital light processing 3D printing