Abstract:Direct-ink-writing (DIW)-based 3D-printing technology combined with the direct-foaming method provides a new strategy for the fabrication of porous materials. We herein report a novel method of preparing porous SiC ceramics using the DIW process and investigate their mechanical and wave absorption properties. We investigated the effects of nozzle diameter on the macroscopic shape and microstructure of the DIW SiC green bodies. Subsequently, the influences of the sintering temperature on the mechanical properties and electromagnetic (EM) wave absorption performance of the final porous SiC-sintered ceramics were also studied. The results showed that the nozzle diameter played an important role in maintaining the structure of the SiC green part. The printed products contained large amounts of closed pores with diameters of approximately 100–200 μm. As the sintering temperature increased, the porosity of porous SiC-sintered ceramics decreased while the compressive strength increased. The maximum open porosity and compressive strength were 65.4% and 7.9 MPa, respectively. The minimum reflection loss (RL) was −48.9 dB, and the maximum effective absorption bandwidth (EAB) value was 3.7 GHz. Notably, porous SiC ceramics after sintering at 1650 °C could meet the application requirements with a compressive strength of 7.9 MPa, a minimum RL of −27.1 dB, and an EAB value of 3.4 GHz. This study demonstrated the potential of direct foaming combined with DIW-based 3D printing to prepare porous SiC ceramics for high strength and excellent EM wave absorption applications.

Si3N4 ceramics with embedded microchannel structures fabricated by high-precision additive manufacturing based on computational fluid dynamics simulations

Si 3 N 4 ceramics with embedded microchannel structures fabricated by high-precision additive manufacturing based on computational fluid dynamics simulations

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Large-size Si 3 N 4 ceramic fabricated by additive manufacturing using long-term stable hydrogel-based suspensions

Large-size Si3N4 Ceramic Fabricated by Additive Manufacturing Using Long-Term Stable Hydrogel-Based Suspensions

Fused Deposition Modeling of Si3N4 Ceramics: A Cost-Effective 3D-Printing Route for Dense and High Performance Non-Oxide Ceramic Materials

Additive manufacturing of complexly shaped SiC with high density via extrusion-based technique – Effects of slurry thixotropic behavior and 3D printing parameters

POLYMER-DERIVED SIC CERAMIC WITH TRIPLY PERIOD MINIMAL SURFACE STRUCTURE FABRICATION THROUGH DIGITAL LIGHT PROCESSING

Fabrication of Si3N4 micro-components by a combined microfabrication process

Microstructures, Mechanical Properties and Electromagnetic Wave Absorption Performance of Porous SiC Ceramics by Direct Foaming Combined with Direct-Ink-Writing-Based 3D Printing

High-strength and low-silicon SiC ceramics prepared by extrusion molding 3D printing

Fabrication of High‐strength Porous SiC‐based Composites with Unidirectional Channels

3D printing of dense structural ceramic microcomponents with low cost: Tailoring the sintering kinetics and the microstructure evolution

Effect of Chemical Vapor Infiltration of Si3n4 on the Mechanical and Dielectric Properties of Porous Si3n4 Ceramic Fabricated by A Technique Combining 3-D Printing and Pressureless Sintering

Mechanical and dielectric properties of porous and wave-transparent Si3N4-Si3N4 composite ceramics fabricated by 3D printing combined with chemical vapor infiltration

Fabrication of Si<sub>3</sub>N<sub>4</sub> Micro-Components by a Combined Microfabrication Process

Design and Manufacturing of Si-Based Non-Oxide Cellular Ceramic Structures through Indirect 3D Printing

Stereolithography-based additive manufacturing of lightweight and high-strength Cf/SiC ceramics

Embedded 3D Printing for Microchannel Fabrication in Epoxy-Based Microfluidic Devices

Processing-microstructure correlations in material extrusion additive manufacturing for carbon fiber reinforced ceramic matrix composites

Microstructure and mechanical properties of porous Si 3 N 4 –SiO 2 ceramics fabricated by a process combining carbothermal reduction and sol–gel infiltration–sintering