Abstract:The optimum balance between mechanical properties and gloss of acrylonitrile–styrene–acrylate resin by controlling poly(n‐butyl acrylate) particle size. Preparation of acrylonitrile–styrene–acrylate (ASA) with high gloss and superior impact properties is still challenging. Here, we developed a new strategy for the preparation of ASA resins by a selective redox initiation method based on a semi‐continuous emulsion polymerization technique. A series of ASA core‐shell impact modifiers were firstly obtained by grafting styrene (St) and acrylonitrile (AN) onto poly(n‐butyl acrylate) (PBA) seeded latexes of different sizes. The ASA core‐shell impact modifier was then used to toughen the styrene–acrylonitrile copolymer (SAN). The synergistic effects between the single particle size of the rubber phase and different particle sizes were systematically investigated, and the mechanical properties of SAN‐toughened resins at various particle sizes of the rubber phase were analyzed. The results revealed that toughened SAN with small particle sizes possessed better gloss, and the impact strength of the doped small‐particle toughened SAN was much higher than that of the single particle size toughened SAN. The ASA graft powders synthesized from large particle PBA (particle size 316 nm) and small particle PBA (particle size 99 nm), respectively, were mixed at a 50/50 ratio and blended with SAN resin, a gloss level reaching 95, and an impact performance of 275 J/m values almost twice those of a single particle size toughened SAN. Highlights Acrylonitrile–styrene–acrylate resins with an impact strength of 275 J/m and gloss of 95 were prepared. The balance between mechanical properties and gloss of acrylonitrile–styrene–acrylate resin was obtained. Polymerization was initiated at low temperature.

Control of the Composition of Matrix Resin for the Design of MABS Resin with Good Transparency and Toughness

Abs/蒙脱土纳米复合材料的制备、结构及性能

Toughening Effect of Poly(Ethene-Co-1-Butene)-Graft-Methyl Methacrylate and Acrylonitrile on Styrene-Acrylonitrile Copolymer (San)

Compatibilizing and toughening of the styrene and acrylonitrile copolymer and core‐shell impact modifier obtained by agglomerate technologies

Achieving optimum balance between mechanical properties and gloss of acrylonitrile–styrene–acrylate resin through control of rubber particle size distribution

Influence of the Tert‐dodecyl Mercaptan Content in Poly(acrylonitrile‐butadiene‐styrene) on Properties of Chlorinated Polyvinyl Chloride/poly(acrylonitrile‐butadiene‐styrene) Blends

Structure and Properties of Heat‐resistant ABS Resins Innovated by NSM Random Copolymer

Effect of polybutadiene grafted methyl methacrylate copolymer on the mechanical performance of PC/ABS composites

Mechanical and Morphological Properties and Deformation Mechanisms of Acrylonitrile-Butadiene-Styrene/Poly(ϵ-Caprolactone) Blends with Varied Matrix Composition

Blending ABS resin and its effect on structure and properties of PC/ABS BLEND alloy

3D-Printable ABS Blends with Improved Scratch Resistance and Balanced Mechanical Performance

Toughening of Poly(butylene Terephthalate) with Epoxy-Functionalized Acrylonitrile–butadiene–styrene

Preparation and Mechanical Properties of Toughened ABS Resin via Bulk Polymerization

Investigation of the Properties of PBT/ABS-g-GMA Blends Modified with Epoxy Resin of Mid-Molecular Weights

Research on effect of ABS,MAH,DCP on property of PA6/ABS blend

Blends of rABS and SEBS: Influence of In-Situ Compatibilization on the Mechanical Properties

Structure and Properties of Isosorbide type Polycarbonate/ABS Blend

Application of solubility parameters in the preparation of PMMA with permanent antistatic, high toughness, and excellent optical properties

Role of in‐situ polymethyl‐methacrylate in addition type silicone rubber with specific reference to adhesion and damping properties

The Preparation of Mah/St Multi-Monomer Melt Grafting on Abs and Its Compatibilizer Effect on Pa6/Abs Blends

Properties of Poly(butylene Terephthalate)/bisphenol A Polycarbonate Blends Toughening with Epoxy-Functionalized Acrylonitrile–Butadiene–Styrene Particles