Abstract:Na‐free solution‐processed CISSe solar cells present inferior performance due to the poor crystallinity of the absorber. By NaCl pre‐selenization treatment (Pre‐ST), the crystallinity of the submicron CISSe absorber significantly improves and grain boundaries remarkably decrease compared to the Na‐free absorber. Such high‐quality submicron CISSe absorber shows improved PV performance. Low‐cost solution‐processed CuIn(S,Se)2 (CISSe) has great potential for large‐scale production of photovoltaics (PV). However, low power conversion efficiency caused by poor crystallinity is one of the main drawbacks compared to vacuum‐processed CISSe solar cells. In this work, three strategies for sodium (Na) incorporation into solution‐processed CISSe by soaking in sodium chloride (NaCl) aqueous‐ethanol solution [1 molarity (M) for 10 minutes (min)], either prior to absorber deposition (pre‐deposition treatment, Pre‐DT), before selenization (pre‐selenization treatment, Pre‐ST), or after selenization (post‐selenization treatment, PST) are researched. The Pre‐ST CISSe solar cells achieve a better PV performance than those from the other two strategies of Na incorporation. For optimization, soaking times (5, 10, and 15 min) and NaCl concentrations (from 0.2 to 1.2 m) of the Pre‐ST are researched. The highest efficiency achieved is 9.6% with an open‐circuit voltage (Voc) of 464.5 mV, a short‐circuit current density (jsc) of 33.4 mA cm−2, and a fill factor (FF) of 62.0%. Compared to the reference CISSe solar cell, Voc, jsc, FF, and efficiency of the champion Pre‐ST CISSe device are improved absolutely by 61.0 mV, 6.5 mA cm−2, 9%, and 3.8%, respectively. Simultaneously, the open‐circuit voltage deficit, the back contact barrier, and the bulk recombination are found to be reduced for Pre‐ST CISSe.

8.0% Efficient Submicron CuIn(S,Se)2 Solar Cells on Sn:In2O3 Back Contact Via a Facile Solution Process

8.0% Efficient Submicron CuIn(S,Se) 2 Solar Cells on Sn:In 2 O 3 Back Contact via a Facile Solution Process

Formation of Alloyed Cu2CoxZn1-xSn(S,Se)4 Absorption Layer and Its Application in Solar Cells.

Solution‐Processed Bifacial Cu(In, Ga)(S, Se)2 Thin Film Solar Cells with a Frontside Power Efficiency of 9.73%

An Efficient S and Se Co-Annealing Strategy for Performance Enhancement of Solution-Processed Submicron CuIn(S,Se)2 Solar Cells

Back Contact Plasma Treatment Enables 14.5% Efficient Solution‐Processed CuIn(S,Se)2 Solar Cells

Cuin(S,Se)(2) Thin Films Prepared from A Novel Thioacetic Acid-Based Solution and Their Photovoltaic Application

Rear Interface Engineering in Solution‐Processed Submicron Cu(In,Ga)(S,Se)2 Solar Cells on Transparent Sn:In2O3 Back Contact

Sodium Incorporation for Performance Improvement of Solution‐Processed Submicron CuIn(S,Se)2 Thin Film Solar Cells

A Facile Molecular Precursor-Based Cu(In,Ga)(S,Se)2solar Cell with 8.6% Efficiency

Sb2Se3 thin film solar cells in substrate configuration and the back contact selenization

10.24% Efficiency of Flexible Cu2 ZnSn(S,Se)4 Solar Cells by Pre-Evaporation Selenization Technique

Reactive Close-Spaced Sublimation Processed CuSbSe2 Thin Films and Their Photovoltaic Application

Carbon Impurity Minimization of Solution-Processed, Thin-Film Photovoltaics via Ligand Engineering of CuInS 2 Nanoparticles

10.3%-Efficient Submicron-Thick Cu(In,Ga)Se2 Solar Cells with Absorber Fabricated by Sputtering In2Se3, CuGaSe2 and Cu2Se Targets

Non-Hydrazine Solution Processed Culn(Se,S)(2) Photovoltaic Device

Segmented Control of Selenization Environment for High‐Quality Cu2ZnSn(S,Se)4 Films Toward Efficient Kesterite Solar Cells

InCl3-modified SnO2 As an Electron Transporting Layer for Cd-free Antimony Selenide Solar Cells

8.36% Efficient CZTS Solar Cells on Transparent Electrode Via Solution Processing

Cu2ZnSnSSe4 Solar Cells with 9.6% Efficiency Via Selenizing Cu-Zn-Sn-S Precursor Sputtered from a Quaternary Target

Achieving 11.95% Efficient Cu2ZnSnSe4 Solar Cells Fabricated by Sputtering a Cu-Zn-Sn-Se Quaternary Compound Target with a Selenization Process