Abstract:The surface Ga content for a CIGSe absorber was closely related to variation in the open-circuit voltage (VOC), while it was generally low on a CIGSe surface fabricated by two-step selenization. In this work, a solution-processed surface treatment based on spin-coating GaCl3 solution onto a CIGSe surface was applied to increase the Ga content on the surface. XPS, XRD, Raman spectroscopy, and band gap extraction based on the external quantum efficiency response demonstrated that GaCl3 post deposition treatment (GaCl3–PDT) can be used to enhance the Ga content on the surface of a CIGSe absorber. Meanwhile, a solution-processed surface treatment with KSCN (KSCN–PDT) was employed to form a transmission barrier for holes by moving the valence band maximum downward and decreasing the interface recombination between the CdS and CIGSe layers. Admittance spectroscopy results revealed that deep defects were passivated by GaCl3–PDT or KSCN–PDT. By applying the combination of GaCl3–PDT and KSCN–PDT, a champion device was realized that exhibited an efficiency of 13.5% with an improved VOC of 610 mV. Comparing the efficiency of the untreated CIGSe solar cells (11.7%), the CIGSe device efficiency with GaCl3–PDT and KSCN–PDT exhibited 15% enhancement.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.1c00270?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.1c00270</a>.XPS peaks of Se 3p for the CIGSe absorbers untreated and treated by GaCl3–PDT, KSCN–PDT, and GaCl3&KSCN–PDT; Eg calculated from the transmittance of the CdS thin film; and UPS spectra for the CdS thin film (<a class="ext-link" href="/doi/suppl/10.1021/acsami.1c00270/suppl_file/am1c00270_si_001.pdf">PDF</a>).This article has not yet been cited by other publications.

Solution‐Processed Bifacial Cu(In, Ga)(S, Se)2 Thin Film Solar Cells with a Frontside Power Efficiency of 9.73%

8.0% Efficient Submicron CuIn(S,Se)2 Solar Cells on Sn:In2O3 Back Contact Via a Facile Solution Process

8.0% Efficient Submicron CuIn(S,Se) 2 Solar Cells on Sn:In 2 O 3 Back Contact via a Facile Solution Process

Bifacial Photovoltaic Performance of Semitransparent Ultrathin Cu(In,Ga)Se2 Solar Cells with Front and Rear Transparent Conducting Oxide Contacts

13.6%-Efficient Cu(In,Ga)Se-2 Solar Cell with Absorber Fabricated by Rf Sputtering of (In,ga)(2)se-3 and Cu Se Targets

Rear Interface Engineering in Solution‐Processed Submicron Cu(In,Ga)(S,Se)2 Solar Cells on Transparent Sn:In2O3 Back Contact

Semitransparent and Bifacial Ultrathin Cu(In,Ga)Se2 Solar Cells Via a Single-Stage Process and Light-Management Strategy

Bifacial and Semitransparent Sb2(S,Se)3 Solar Cells for Single‐Junction and Tandem Photovoltaic Applications

Transparent MoS<sub>2</sub>/PEDOT Composite Counter Electrodes for Bifacial Dye-Sensitized Solar Cells

Inkjet‐Printed Cu(In,Ga)(S,Se)2 Thin Film Solar Cells Exceeding 15% Power Conversion Efficiency

10.3%-Efficient Submicron-Thick Cu(In,Ga)Se2 Solar Cells with Absorber Fabricated by Sputtering In2Se3, CuGaSe2 and Cu2Se Targets

New Solution-Processed Surface Treatment to Improve the Photovoltaic Properties of Electrodeposited Cu(In,Ga)Se 2 (CIGSe) Solar Cells

Sb2Se3 thin film solar cells in substrate configuration and the back contact selenization

Cu(In, Ga)(Se, S)2 thin‐film technology: Aspects of historical development, current status, and future prospects

Highly Efficient Bifacial CsPbIBr2 Solar Cells with a TeO2/Ag Transparent Electrode and Unsymmetrical Carrier Transport Behavior.

Enhanced performance of GeSe thin-film solar cells via bifacial charge transport materials design

Efficiency enhancement of copper indium gallium selenide solar cells fabricated on polyimide foils with multiple metal layers

Back Contact Plasma Treatment Enables 14.5% Efficient Solution‐Processed CuIn(S,Se)2 Solar Cells

Regulating Energy Band Alignment via Alkaline Metal Fluoride Assisted Solution Post‐Treatment Enabling Sb 2 (S,Se) 3 Solar Cells with 10.7% Efficiency

Selenium‐Rich Sb2(S,Se)3 Thin Films Deposited via Sequential Chemical Bath Deposition for High‐Efficiency Solar Cells

Regulating Energy Band Alignment Via Alkaline Metal Fluoride Assisted Solution Post‐Treatment Enabling Sb2(S,Se)3 Solar Cells with 10.7% Efficiency