Abstract:Actomic layer deposition processed SnOx is introduced as electron transport layer in Sb2Se3 thin‐film solar cells. An additional post‐annealing can remarkably enhance the photovoltaic performance, thanks to the optimized carrier dynamics under simultaneously improving the properties of SnOx, Sb2Se3/SnOx heterojunction and Sb2Se3 absorber layer. A stimulating efficiency of 7.39% represents the record value for Cd‐free substrate structured Sb2Se3 solar cells. Antimony selenide (Sb2Se3) is a highly promising photovoltaic material thanks to its outstanding optoelectronic properties, as well as its cost‐effective and eco‐friendly merits. However, toxic CdS is widely used as an electron transport layer (ETL) in efficient Sb2Se3 solar cells, which largely limit their development toward market commercialization. Herein, an effective green Cd‐free ETL of SnOx is introduced and deposited by atomic layer deposition method. Additionally, an important post‐annealing treatment is designed to further optimize the functional layers and the heterojunction interface properties. Such engineering strategy can optimize SnOx ETL with higher nano‐crystallinity, higher carrier density, and less defect groups, modify Sb2Se3/SnOx heterojunction with better interface performance and much desirable "spike‐like" band alignment, and also improve the Sb2Se3 light absorber layer quality with passivated bulk defects and prolonged carrier lifetime, and therefore to enhance carrier separation and transport while suppressing non‐radiative recombination. Finally, the as‐fabricated Cd‐free Mo/Sb2Se3/SnOx/ITO/Ag thin‐film solar cell exhibits a stimulating efficiency of 7.39%, contributing a record value for Cd‐free substrate structured Sb2Se3 solar cells reported to date. This work provides a viable strategy for developing and broadening practical applications of environmental‐friendly Sb2Se3 photovoltaic devices.

Reactively Sputtered CdS:O Buffer Layers for Substrate Sb2Se3 Solar Cells

Heterostructured CdS Buffer Layer for Sb2Se3 Thin Film Solar Cell

Thermal evaporation–deposited hexagonal CdS buffer layer with improved quality, enlarged band gap, and reduced band gap offset to boost performance of Sb2(S,Se)3 solar cells

Zn(O,S) Buffer Layer for in Situ Hydrothermal Sb 2 S 3 Planar Solar Cells

Optimizing interface energy band alignment in Cd-free Sb2Se3 solar cells by controlling the oxygen content of In2(O,S)3 buffer layer to improve the efficiency: A simulation study

Zinc Chloride‐treated Indium Sulfide as Buffer Layer for Cd‐free Antimony Selenide Solar Cells

In Situ Investigation of Interfacial Properties of Sb2Se3 Heterojunctions

Self-passivated CdS Buffer Layer for Antimony Sulfide Solar Cells

High-efficiency Sb2Se3 thin-film solar cells based on Cd(S,O) buffer layers prepared via spin-coating

Sb2Se3 solar cells employing metal-organic solution coated CdS buffer layer

Study on the Performance of Oxygen-Rich Zn(O,S) Buffers Fabricated by Sputtering Deposition and Zn(O,S)/Cu(In,Ga)(S,Se) 2 Interfaces

Molecular Beam Epitaxy Deposition of In Situ O‐Doped CdS Films for Highly Efficient Sb2(S,Se)3 Solar Cells

Sputtered and Selenized Sb2Se3 Thin-Film Solar Cells with Open-Circuit Voltage Exceeding 500 Mv

Enhancing the properties of Cd-free MgZnS buffer for solar cells by co-sputtering ZnS and Mg targets

Sputtering Al2O3 as an effective interface layer to improve open-circuit voltage and device performance of Sb2Se3 thin-film solar cells

Characterizing ZnMgO/Sb2Se3 Interface for Solar Cell Applications

Optimizing Crystal Orientation and Defect Mitigation in Antimony Selenide Thin-Film Solar Cells through Buffer Layer Energy Band Adjustment

Cu(In,Ga)Se2 Solar Cells with Double Layered Buffers Grown by Chemical Bath Deposition

Electron Transport Layer Engineering Induced Carrier Dynamics Optimization for Efficient Cd‐Free Sb2Se3 Thin‐Film Solar Cells

Stable 6%-efficient Sb2Se3 solar cells with a ZnO buffer layer

Post-deposition annealing and interfacial ALD buffer layers of Sb$_2$Se$_3$/CdS stacks for reduced interface recombination and increased open-circuit voltages