Abstract:Hydrothermal deposition is emerging as a highly potential route for antimony-based solar cells, in which the Sb2(S,Se)3 is typically in situ grown on a common toxic CdS buffer layer. The narrow band gap of CdS causes a considerable absorption in the short-wavelength region and then lowers the current density of the device. Herein, TiO2 is first evaluated as an alternative Cd-free buffer layer for hydrothermally derived Sb2S3 solar cells. But it suffers from a severely inhomogeneous Sb2S3 coverage, which is effectively eliminated by inserting a Zn(O,S) layer. The surface atom of sulfur in Zn(O,S) uniquely provides a chemical bridge to enable the quasi-epitaxial deposition of Sb2S3 thin film, confirming by both morphology and binding energy analysis using DFT. Then the results of the first-principles calculations also show that Zn(O,S)/Sb2S3 has a more stable structure than TiO2/Sb2S3. The resultant perfect Zn(O,S)/Sb2S3 junction, with a suitable band alignment and excellent interface contact, delivers a remarkably enhanced JSC and VOC for Sb2S3 solar cells. The device efficiency with the TiO2/Zn(O,S) buffer layer boosts from 0.54% to 3.70% compared with the counterpart of TiO2, which has a champion efficiency of Cd-free Sb2S3 solar cells with a structure of ITO/TiO2/Zn(O,S)/Sb2S3/Carbon/Ag by in situ hydrothermal deposition. This work provides a guideline for the hydrothermal deposition of antimony-based films upon a nontoxic buffer layer.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.1c12501.Additional some crystal structures, band gap, and surface morphology of buffer layer and device, and some photoelectric characteristics of the Sb2S3 solar cells with Zn(O,S) (PDF)This article has not yet been cited by other publications.

High-efficiency Sb2Se3 thin-film solar cells based on Cd(S,O) buffer layers prepared via spin-coating

Molecular Beam Epitaxy Deposition of In Situ O‐Doped CdS Films for Highly Efficient Sb2(S,Se)3 Solar Cells

Sb2Se3 solar cells employing metal-organic solution coated CdS buffer layer

Heterostructured CdS Buffer Layer for Sb2Se3 Thin Film Solar Cell

Thermal evaporation–deposited hexagonal CdS buffer layer with improved quality, enlarged band gap, and reduced band gap offset to boost performance of Sb2(S,Se)3 solar cells

Zinc Chloride‐treated Indium Sulfide as Buffer Layer for Cd‐free Antimony Selenide Solar Cells

Reactively Sputtered CdS:O Buffer Layers for Substrate Sb2Se3 Solar Cells

Efficient CdS buffered TiO2 electronic transport layer for Sb2S3 solar cells by a facile spinning coating process

Solvent‐Assisted Hydrothermal Deposition Approach for Highly‐Efficient Sb2(S,Se)3 Thin‐Film Solar Cells

Aqueous-Solution-Based Approach Towards Carbon-Free Sb2 S3 Films for High Efficiency Solar Cells.

Stable 6%-efficient Sb2Se3 solar cells with a ZnO buffer layer

Oxygen Content Modulation Toward Highly Efficient Sb2Se3 Solar Cells

Realizing zinc-doping of CdS buffer layer via partial electrolyte treatment to improve the efficiency of Cu2ZnSnS4 solar cells

Pulsed laser deposition of antimony selenosulfide thin film for efficient solar cells

An effective combination reaction involved with sputtered and selenized Sb precursors for efficient Sb2Se3 thin film solar cells

Zn(O,S) Buffer Layer for in Situ Hydrothermal Sb 2 S 3 Planar Solar Cells

Optimisation of Sb2S3 thin-film solar cells via Sb2Se3 post-treatment

Regulating Deposition Kinetics via A Novel Additive-assisted Chemical Bath Deposition Technology Enables 10.57%-efficient Sb2Se3 Solar Cells

Water Additive Enhanced Solution Processing of Alloy Sb2(S1−xSex)3‐Based Solar Cells

Optimizing Crystal Orientation and Defect Mitigation in Antimony Selenide Thin-Film Solar Cells through Buffer Layer Energy Band Adjustment

Fabricating High‐Efficiency Sb2(S,Se)3 Solar Cells by Novel Additive‐Assisted Longitudinal Component Engineering