Abstract:Antimony chalcogenides are widely studied as a light-absorbing material due to their merits of low toxicity, efficient cost, and excellent photovoltaic properties. However, the band gaps of antimony selenide (approximately 1.1 eV) and antimony sulfide (approximately 1.7 eV) both deviate from the optimal detailed balance band gap (∼1.3 eV) for terrestrial single-junction solar cells. Notably, the band gap of Sb2(S, Se)3 can be tunable in the range from 1.1 to 1.7 eV, which can cover the detailed balance band gap. In this work, the vapor transport deposition method with two independent evaporation sources is used to deposit Sb2(S, Se)3 thin films. By carefully optimizing the evaporation temperature and the start evaporation time of the Sb2Se3 and Sb2S3 sources, a suitable band gap of 1.33 eV is obtained. Finally, on the basis of the optimal Sb2(S, Se)3 films, Sb2(S, Se)3 solar cells without a hole transport layer achieved an efficiency of 7.03%.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.1c10758.Saturated vapor pressure curves of Sb2Se3 and Sb2S3; temperature–time curves of Sb2Se3 and Sb2S3 sources; top-view SEM images at different Sb2Se3 and Sb2S3 source temperatures; XRD diffraction pattern under different Sb2Se3 and Sb2S3 source temperatures; transmission spectroscopy at different Sb2Se3 and Sb2S3 source temperatures; schematic diagram of thin-film light absorption; heating process of the uniform Sb2(S, Se)3 films and band gaps of Sb2(S, Se)3 films; 1/C2–V curves of the devices; band gaps of the devices obtained from EQE data; J–V curves under different light intensities; atomic and ionic radii; material parameters for SCAPS simulations; CdS trap state parameters for SCAPS simulations; and Sb2(S, Se)3 trap state parameters (PDF)This article has not yet been cited by other publications.

Vapor Transport Deposition of Sb2(S,Se)3 Solar Cells with Continuously Tunable Band Gaps

Vapor Transport Deposition of Sb 2 (S,Se) 3 Solar Cells with Continuously Tunable Band Gaps

Temperature Sensitivity of Adjustable Band Gaps of Sb2(S, Se)3 Solar Cells Via Vapor Transport Deposition

HTL-Free Sb 2 (S, Se) 3 Solar Cells with an Optimal Detailed Balance Band Gap

Over 7% Efficiency of Sb2(S,Se)3 Solar Cells Via V‐Shaped Bandgap Engineering

HTL-Free Sb<sub>2</sub>(S, Se)<sub>3</sub> Solar Cells with an Optimal Detailed Balance Band Gap

Improved Open‐Circuit Voltage of Sb2Se3 Thin‐Film Solar Cells Via Interfacial Sulfur Diffusion‐Induced Gradient Bandgap Engineering

Chemical Etching Induced Surface Modification and Gentle Gradient Bandgap for Highly Efficient Sb2(S,Se)3 Solar Cell

Vapor Transport Deposition of Highly Efficient Sb2(S,Se)3 Solar Cells Via Controllable Orientation Growth

Sequential Coevaporation and Deposition of Antimony Selenosulfide Thin Film for Efficient Solar Cells

Improved Open‐Circuit Voltage of Sb 2 Se 3 Thin‐Film Solar Cells Via Interfacial Sulfur Diffusion‐Induced Gradient Bandgap Engineering

Interface Etching Leads to the Inversion of the Conduction Band Offset Between the CdS/Sb2Se3 Heterojunction and High-Efficient Sb2Se3 Solar Cells

Sb-2(Se1-xSx)(3) Thin-Film Solar Cells Fabricated by Single-Source Vapor Transport Deposition

Magnetron Sputtered Sb2Se3-based Thin Films Towards High Performance Quasi-Homojunction Thin Film Solar Cells

Controllable vapor transport deposition of efficient Sb<sub>2</sub>(S,Se)<sub>3</sub> solar cells via adjusting evaporation source area

Controllable vapor transport deposition of efficient Sb2(S,Se)3 solar cells via adjusting evaporation source area

Se-Elemental Concentration Gradient Regulation for Efficient Sb2(S,Se)3 Solar Cells With High Open-Circuit Voltages

Fabricating over 7%-efficient Sb2(S,Se)3 thin-film solar cells by vapor transport deposition using Sb2Se3 and Sb2S3 mixed powders as the evaporation source

High Efficiency Sb2(S, Se)3 Thin-Film Solar Cells by Substrate-Temperature-controlled Vapor Transport Deposition Method

Temperature‐Gradient Solution Deposition Amends Unfavorable Band Structure of Sb2(S,Se)3 Film for Highly Efficient Solar Cells

All-Vacuum-Processed Sb<sub>2</sub>(S,Se)<sub>3</sub> Thin Film Photovoltaic Devices via Controllable Tuning Seed Orientation