Abstract:This study aims at introducing the back stress of anisotropic strain-hardening into the crystal plasticity theory and demonstrating the rationality of this crystal plasticity model to describe the evolution of the subsequent yield surface of polycrystalline aluminum at the mesoscopic scale under complex pre-cyclic loading paths. By using two different scale finite element models, namely a global finite element model (GFEM) as the same size of the thin-walled tube specimen used in the experiments and a 3D cubic polycrystalline aggregate representative volume element (RVE) model, the evolution of the subsequent yield surface for different unloading cases after 30 pre-cycles is further performed by experiments and numerical simulations within a crystal plasticity finite element (CPFE) frame. Results show that the size and shape of the subsequent yield surfaces are extremely sensitive to the chosen offset strain and the pre-cyclic loading direction, which present pronounced anisotropic hardening through a translation and a distortion of the yield surface characterized by the obvious "sharp corner" in the pre-deformation direction and "flat" in the reverse direction by the definition of small offset strain, while the subsequent yield surface exhibits isotropic hardening reflected by the von Mises circle to be distorted into an ellipse by the definition of large offset strain. In addition, the heterogeneous properties of equivalent plastic strain increment are further discussed under different offset strain conditions. Modeling results from this study show that the heterogeneity of plastic deformation decreases as a law of fraction exponential function with the increasing offset strain. The above analysis indicates that anisotropic hardening of the yield surface is correlated with heterogeneous deformation caused by crystal microstructure and crystal slip. The crystal plasticity model based on the above microscopic mechanism can accurately capture the directional hardening features of the yield surface.

The Progressive Intensification and Attenuation of Yield Point Phenomenon in a New Polycrystalline Zirconium Alloy: Anisotropic Response of Work Hardening-Softening Transition

Activating Continuous Dislocation Pinning Enhanced Toughness of Nanocomposite Coating Through Specially Oriented Semicoherent Heterointerface Lattice Distortion

The Elimination of the Yield Point Phenomenon in a New Zirconium Alloy: Influence of Degree of Recrystallization on the Tensile Properties

The Gradual Disappearance and Re-Appearance of Yield Drop by Modulating the Pre-Strain History in a New Zirconium Alloy: Dislocation Decomposition and Recombination

Strain Hardening Versus Softening: Anisotropic Response of Strain Hardening-Softening Transition in a Polycrystalline Zirconium Alloy at Room Temperature from Dislocation Viewpoint

Enhancement of Yield Strength in Zirconium Metal Through High-Pressure Induced Structural Phase Transition

An Extraordinary Enhancement of Strain Hardening in Fine-Grained Zirconium

The Gradual Disappearance of Yield Plateau in Zr–Sn–Nb–Fe–Mo Alloy by the Trace Addition of Cr and V

Investigation of Yield Surfaces Evolution for Polycrystalline Aluminum after Pre-Cyclic Loading by Experiment and Crystal Plasticity Simulation

Understanding the Mechanism for the In-Plane Yielding Anisotropy of a Hot-Rolled Zirconium Plate

A quasi in-situ study on the work hardening and softening mechanisms of Ti–33Zr–12Al–6V alloy

Confluent Effects of Initial Dislocation Microstructures on Yield Behavior in Single-Crystal Tungsten at High Temperature

Surface Orientation Dependence of Irradiation-Induced Hardening in a Polycrystalline Zirconium Alloy

A Study of the Sharp Yield Point of a Ti-22Al-25Nb Alloy

Micro-scale mechanism for cyclic deformation behavior in Zirconium under low-cycle-fatigue loading

Strain Rate and Anisotropic Effects on Incipient Plastic Deformation of Zn–Cu–Ti Alloy Sheets

High Strain Rate Deformation Behavior of Zirconium at Elevated Temperatures

Excellent Work-Hardening in ZrCu/NiNb Amorphous/amorphous Nanolaminates

An Inverse Hall-Petch Behavior and Improving Toughness in Translucent Nanocrystalline High-entropy Zirconate Ceramic

High Pressure Phase-Transformation Induced Texture Evolution and Strengthening in Zirconium Metal: Experiment and Modeling

Precipitation Evolution of Al–Zr–Yb Alloys During Isochronal Aging