Abstract:The tensile behavior of Ti6Al4V–5Cu alloy studied in the temperature range of 450–550 °C at the strain rate interval of 10 −3 -10 −1 s −1 . Alloy deformation behavior, microstructure evolution, and its relative internal structure changes due to deformation were investigated. The tensile behavior of the alloy had elucidated in terms of change in true stress-strain relationship. At 450 °C, the alloy showed the decrease of peak stress at the strain rate interval of 10 −3 -10 −2 s −1 , which suggests Ti6Al4V–5Cu plastic flow behavior, was quite different. The alloy exhibited an elongation (El) of 28% at 450 °C in a strain rate of 10 −3 s −1 . At 10 −3 s −1 , the El of the alloy decreased with the increase of forming temperature. However, at 10 −2 s −1 and 10 −1 s −1 , the El increased with the rising of temperature. Scanning electron microscope (SEM) was used to investigate the microstructure of Ti6Al4V–5Cu alloy. The alloy grain boundaries (GBs) were found as continuous and discontinuous structural features, especially the high angle grain boundaries (HAGBs). The GB feature has contributed to the initiation of micro-cracks because of the creation of weakest regions in the material during deformation. The nature of GB geometry has also a tremendous contribution to the workability of Ti6Al4V–5Cu alloy at low forming temperatures. The presence of a high amount (%) LAGBs and the serrated nature of HAGBs structures determined the pull to grain pieces. The deformation mechanism of the Ti6Al4V–5Cu alloy at low forming temperatures was accomplished initially by boundary serration phenomenon due to strain-induced GB migration related to heat treatment at low strain condition, then by initiation of recrystallized grains-triggered by the plasticity behavior of strain induced sub-boundaries, and finally by the development of deformed grains generated by the reduction in corrugation propensity of GBs due to high strain condition.

A quasi in-situ study on the work hardening and softening mechanisms of Ti–33Zr–12Al–6V alloy

Microstructure Regulation and Strength-Elongation Synergy of the Near Alpha TZAM Alloy Via Thermomechanical Processing

Thermal stability and its effects on the mechanical properties of rapidly solidified Al-Ti alloys

In-situ Investigation Via High Energy X-ray Diffraction of Stress-Induced(0002)α→(110)β Transformation in a Ti-5.5Mo-7.2Al-4.5Zr-2.6Sn-2.1Cr Alloy

Microstructure and microhardness evolution of Ti-10V-2Fe-3Al alloy under tensile/torsional deformation modes

Effect of microstructures on mechanical properties of Ti‐6.5Al‐2Sn‐4Zr‐4Mo‐1W‐0.2Si alloy

In-Situ SEM Observation on Fracture Behavior of Titanium Alloys with Different Slow-Diffusing β Stabilizing Elements

Microstructure evolution, tensile properties and internal structure transformation study on Ti6Al4V–5Cu anti-bacterial alloy during uniaxial tensile straining at low forming temperature

Study on high temperature tensile constitutive behavior and deformation mechanism of Ti-47.5Al-2.5 V-1.0Cr-0.2Zr alloy

In situ tensile test of selective laser melted Ti-6.5Al-2Zr-1Mo-1V alloy at different stages of martensite decomposition

In-situ investigation on tensile properties of a novel Ti/Al composite sheet

From Strain Softening to Strain Hardening in Submicron Scale Ti2448 Associated with Slip Mode Transition Mediated by Nanoscale Martensitic Transformation

Stable strain hardening behavior of Ti-4Al-5Mo-5V-5Cr-1Nb alloy during plastic deformation

In Situ Electron Backscatter Diffraction Study of Deformation Inhomogeneity under Uniaxial Tension of Laser Melting Deposited TA15 Alloy

Effect of Solution Temperature on Microstructure and Mechanical Properties of Ti–5Al5Mo5V3Cr1Zr Alloy

High-temperature tensile deformation behavior and microstructure evolution of Ti55 titanium alloy

Multiple deformation mechanisms induce high work hardening in Ti–5Al–7.5 V alloy via transformed β matrix

Microstructural characteristics and recrystallization mechanism of Ti-6.5Al–2Zr–1Mo–1V alloy during two-stage hot deformation

Drastic enhancement in hot-workability and microstructural refinement of TiAl alloys via martensitic transformation: A comparative study

Stress-induced martensitic transformation in a β-solution treated Ti–10V–2Fe–3Al alloy during compressive deformation

Microstructural and mechanical behavior of Al-Mg-Mn-Sc-Zr alloy subjected to multi-axial forging at room temperature