Abstract:The texture evolution, crystal orientation-dependent deformation mechanism and mechanical properties of the Mg-5.5Gd-4.4Y-1.1Zn-0.5Zr (wt%) alloy sheet with bimodal grain structure during hot rolling were investigated in this study. The pre-rolled sheet possesses the texture with c-axis randomly distributed in rolling-transverse plane. During the hot rolling deformation, the initial texture is gradually changed to an uncommon texture with c-axis continuously distributed between transverse direction (TD) and normal direction (ND) of the rolled sheet. The formation of the texture is related to the orientation-dependent deformation mechanism of coarse grains. For the coarse grains with c-axis close to rolling direction (RD), {10-12} twinning was identified to be the dominated deformation mechanism. With the activation of twinning, the c-axis of the matrix is reoriented towards ND. For the coarse grains with c-axis near TD, prism slip and kink deformation were figured out as the dominated deformation modes. In early stage of the hot rolling deformation, the c-axis of the grains remains in TD with the activation of prism slip. Afterwards, kink deformation activates and the c-axis of the grains is rotated away from TD towards ND with different degrees. In addition, the mechanical properties of rolled sheets were examined and the results demonstrate that yield strength and tensile strength are gradually improved by rolling deformation. Nevertheless, the improvement of yield strength in RD is much greater than that in TD and a serious yield strength anisotropy is shown in the rolled sheet. The strong yield strength anisotropy derives from the variation of texture strengthening in the RD and TD due to the formation the texture with c-axis continuously distributed between TD and ND.

Understanding the Mechanism for the In-Plane Yielding Anisotropy of a Hot-Rolled Zirconium Plate

Anisotropic Deformation Mechanisms of Rolling-Textured Zircaloy-4 Alloy by a Crystal Plasticity Model

The Action Mechanism of Rolling Texture on the Anisotropic Behavior of a Pure Titanium Plate

Anisotropy of Yielding/Hardening and Micro-Inhomogeneity of Deforming/Rotating for A Polycrystalline Metal under Cyclic Tension Compression

In Situ EBSD/HR-DIC-based Investigation on Anisotropy Mechanism of a Near Α Titanium Plate with Strong Transverse Texture

Deformation mechanism, orientation evolution and mechanical properties of annealed cross-rolled Mg-Zn-Zr-Y-Gd sheet during tension

Effect of Loading Direction on the Deformation and Annealing Behavior of a Zirconium Alloy

Experimental and Mechanistic Investigation on the Plastic Anisotropic Deformation Behavior of Α-Phase Titanium Alloy Ti-2Al-2.5Zr

Deformation Mode-Determined Misorientation and Microstructural Characteristics in Rolled Pure Zr Sheet

Microstructure, texture evolution and mechanical anisotropy of Mg-Gd-Y-Zn-Zr alloy sheets produced by unidirectional and cross rolling

Microstructural Evolution and Mechanical Properties in Zr705 During the Rolling Process

Effect of uniaxial loading direction on mechanical responses and texture evolution in cold pilgered Zircaloy-4 tube: Experiments and modeling

Deformation Mechanisms of Zirconium Alloys under Biaxial Tension at Room Temperature

Microstructure and Mechanical Properties of Annealed Mg–0.6wt%Zr Sheets by Unidirectional and Cross Rolling

Influence of Intergranular Mechanical Interactions on Orientation Stabilities During Rolling of Pure Aluminum

A General Yield Function Within the Framework of Linear Transformations of Stress Tensors for the Description of Plastic-Strain-Induced Anisotropy

Effect of Unidirectional Rolling and Cross-Rolling on Microstructure and Mechanical Anisotropy of Mg-Gd-Y-Ag-Zr Plates

Microstructures and Mechanical Properties of a Commercial Pure Zirconium during Rolling and Annealing at Different Temperatures

Texture Evolution, Deformation Mechanism and Mechanical Properties of the Hot Rolled Mg-Gd-Y-Zn-Zr Alloy Containing LPSO Phase

On the Texture Memory Effect of a Cross-Rolled Mg-2Zn-2Gd Plate after Unidirectional Rolling

Microstructure, texture and mechanical anisotropy of Mg-Gd-Y-Zr sheets processed via different rolling routes and reductions