Abstract:To meet the demands of both processing and serving, to the best of our knowledge, this is the first report exhibiting large range control of the yield ratio from 0.31 to 0.96 with decent elongations over 10% in the same alloy with low-cost thermal treatments. The yield ratio of the metastable Ti-30Zr-5Mo alloy was regulated via adjusting trigger stress of the stress-induced phase transformation and work-hardening ability through changing the α phase content. Materials with acicular α phase of different contents were successfully prepared via low-cost thermal treatment. The effects of the α phase content on the stress-induced α ' martensite phase transformation and work hardening behavior were then investigated. In the Ti-30Zr-5Mo alloy with dual phases, due to the crystal difference and element partitioning, the hardness of the α phase is higher than that of the β matrix, and the hardness difference between the phases increases with increasing α phase. In addition to Mo, Zr plays an important role in stabilizing the β phase in high-Zr-containing alloys. Deformation initiates in the β phase of both single-phase and duplex-phase alloys. The deformation mechanism of the β phase is dependent on both the β domain and β stability. Due to the low trigger stress and excellent work hardening ability, stress-induced α ' martensite phase transformation is helpful to lower the yield ratio. As the α phase content increases, the trigger stress increases, and when the α phase content increases to 40%, dislocation slip dominates rather than stress-induced α ' martensite phase transformation, and a high yield strength of 944 MPa is obtained. The α/β phase interfaces act as effective obstacles to hinder dislocation movement and provide working hardening, and the obstruction effect is more significant with an increase in the hardness difference between the α and β phases. The stress-induced α ' phase transformation and/or the deformation coordination between the α and β phases guarantee decent elongations of no less than 10% in the large control of the yield ratio from 0.31 to 0.96 with a yield strength from 254 to 1013 MPa. It paves the way to develop "Unititaniam" alloys for wide possible applications.

The Gradual Disappearance of Yield Plateau in Zr–Sn–Nb–Fe–Mo Alloy by the Trace Addition of Cr and V

Atomic Investigation of Alloying Cr, Ti, Y Additions in a Grain Boundary of Vanadium

The Elimination of the Yield Point Phenomenon in a New Zirconium Alloy: Influence of Degree of Recrystallization on the Tensile Properties

Effect of Trace Zr on Microstructure and Hardness of Al-Zn-Mg-Cu Alloy Prepared under Supergravity

Effects of trace Zn on the deformation mechanisms of Mg‐Gd‐Y‐Zr alloy investigated by in‐situ synchrotron diffraction

The Gradual Disappearance and Re-Appearance of Yield Drop by Modulating the Pre-Strain History in a New Zirconium Alloy: Dislocation Decomposition and Recombination

Effects of alloying elements (Sn, Nb, Cr, and Mo) on the microstructure and mechanical properties of zirconium alloys

Dynamic recrystallization and precipitation behavior of a novel Sc, Zr alloyed Al-Zn-Mg-Cu alloy during hot deformation

Influence of Cr and Yb alloying on the microstructures and fracture characteristics of Al-Zn-Mg-Cu-Zr alloy

Investigation on deformation mechanisms of Zr-1Sn-0.3Nb-0.3Fe-0.1Cr alloy using in situ EBSD/SEM

Influence of Zr on grain orientation, texture, and mechanical properties in hot- and warm-rolled FeCrAl alloys

Regulating Phase Ratio of Β/α and Static Recrystallization of Ti-5Al-5Mo-5Cr-3Nb-2Zr with High Plasticity Alloyed by Vanadium

The Microstructural Characteristics and Mechanical Properties of Nb-16Si-22Ti-2Al-2Cr Alloys with Zr Addition

Microstructures and Mechanical Properties of Cast Nb-Ti-Si-Zr Alloys

Microstructural Analysis on Grain Boundary of Boron– and Zirconium–Containing Wrought Nickel-Based Superalloys

Study on Recrystallization and Correlated Mechanical Properties in Mo-modified Zr-Nb Alloys

Effect of Trace Zinc on the Microstructure and Mechanical Properties of Extruded Mg-Gd-Y-Zr Alloy

Effects of Zr on high temperature deformation and dynamic precipitation of laves phase in Fe–13Cr–5Al–2Mo–0.5Nb–0.4Ta alloy

Microstructural evolution and mechanical property of Al–Zr and Al–Zr–Y alloys

Effects of Zr Addition on the Microstructure and Mechanical Properties of AlCoCrFeNiZrx High-Entropy Alloys

A strategy to regulate the yield ratio of a metastable high Zr-containing β titanium alloy: Synergistic effects of the β domain, β stability and β/α interfaces by varying the α phase content