Abstract:The oxidation behavior of the WC-CoNiFeCr functionally graded cemented carbide (FGCC) has been investigated by isothermal oxidation and composition characterization. The results showed that the oxidation of cemented carbide was closely related to the oxidation temperature and oxidation time, and the oxidation of different elements had a clear sequential order. The Cr element was first selectively oxidized to Cr 2 O 3 , followed by the oxidation of other composing elements of the multi-principal-element alloy (MPEA) binder to M x O y and MWO 4 . The WC was then oxidized to WO 3 , and WO 3 and M x O y were thereafter reacted to form MWO 4 . The binder composition, structural distribution, and WC grain size were the three key factors that affected the oxidation resistance of the cemented carbides. Fine-grained and graded cemented carbides, with CoNiFeCr MPEA binder, had the highest anti-oxidation properties. The FGCC showed lower oxidation of the binder at 600 °C, a denser MWO 4 distribution at 700 °C, and a smaller volume expansion at 800 °C, as compared with the non-graded cemented carbide (CC). Compared with the coarse-grained cemented carbide, the fine-grained cemented carbide had more grain boundaries between the WC and the binder, which resulted in a denser distribution of the binder oxides. WC-20CoNiFeCr had a higher energy barrier for the oxidation reaction and more stable oxidation products than WC-20Co. The results did not only provide theoretical guidance for the understanding of the anti-oxidation mechanism of WC-CoNiFeCr, but they also expanded a new approach for the preparation of cemented carbides with high oxidation resistance.

Wear Resistance of Ultra-Coarse WC-WCoB-Co Cemented Carbide at Different Oxidation Stages

On the Enhanced Wear Resistance of Ultra-Coarse WC-Co Cemented Carbides by WCoB Addition

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

Performance Enhancement of Ultra-Coarse Cemented Carbide by Boride Additives

Preparation of Ultra-Fine WC-Co Cermet and Its Wear Behavior

Selective oxidation induced wear degradation in cemented carbides

Microstructure, Mechanical and Tribological Properties of WC-WCoB Coating

Effect of (Ti,W)C/TaC addition on the early oxidation behavior of surface layer of WC-Co cemented carbides

Microstructure and properties of ultrafine WC–Co–VC cemented carbides with different Co contents

Microstructure and mechanical properties of WC–Co-based cemented carbide with bimodal WC grain size distribution

Ultra-coarse cemented tungsten carbide with (Zr,W)C x precipitates in ceramic phase

Effects of Ni and Cu Additions on Microstructures, Mechanical Properties and Wear Resistances of Ultra-Coarse Grained WC–6Co Cemented Carbides

Preparation, properties and microstructure of high hardness WC-co cemented carbide tool materials for ultra-precision machining

Ultra-coarse Cemented Tungsten Carbide with (zr,w)cx Precipitates in Ceramic Phase

Influences of Cr contents on oxidation behavior of WC-Co-Ni-Cr cemented carbides at 900 °C

Oxidation behavior of functionally graded cemented carbides with CoNiFeCr multi-principal-element alloy binder

Mechanism of the early stages of oxidation of WC–Co cemented carbides

Effect of Cu and CeO2 additives on structure and performance of WC-10Co cemented carbides

Influence of Ru on the microstructure and performance of WC-Co cemented carbides

Promising WC-30WB-10Co Cemented Carbide Coating with Improved Density and Hardness Deposited by High Velocity Oxy-Fuel Spraying: Microstructure and Mechanical Properties

Microstructural characteristics and wear-resistant mechanisms of WC-TiC-co coatings with varying TiC contents