Abstract:In this study, we investigated the effects of nanostructured composite powders (WC-Ni), nickel binder content, and sintering techniques on the morphology and mechanical properties of tungsten carbide. An alternative low-temperature gas-solid reaction route with a short reaction time was employed to produce nanostructured composite powders with 5 and 15 wt% Ni. The powders were consolidated using spark plasma sintering (SPS) and conventional vacuum furnace sintering at temperatures of 1350 °C and 1450 °C. The composite powders were characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), and particle size measurements. The expansion/contraction of the compacted nanocomposite powders was studied through dilatometric analysis. The composite powders exhibited a uniform distribution of Ni, in both compositions. For the WC-5 wt% Ni nanocomposite powders, the average crystallite sizes for WC and Ni were 41.6 nm and 46.2 nm, respectively. While, for the WC-15 wt% Ni nanocomposite, the crystallite sizes for WC and Ni were 45.6 and 38.4 nm. The sintered composites were evaluated through XRD, SEM, measurements of density and Vickers hardness. The enhanced sinterability of the nanostructured powders enabled their consolidation into (WC-Ni) hard metal with densities approaching the theoretical relative density of 96.07 %, even with low binder content (5 wt% Ni). This is attributed to the uniform distribution of Ni and an extensive Ni-WC interface present prior to sintering. The SPS process at 1350 °C produced sintered bodies (WC-5 wt% Ni and WC-15 wt% Ni) with higher Vickers hardness (2322 HV and 1512 HV, respectively) and superior microstructural quality compared to samples produced by conventional vacuum furnace techniques. These results demonstrated that the mechanical properties of the system WC-Ni processed by SPS are superior to those obtained by vacuum furnace. Therefore, WC-Ni hard metals processed by this approach is a promising alternative to conventional hard metals (WC-Co) for a wide range of applications.

Effect of Sintering Atmosphere on the Microstructure and Properties of Nano-Wc Modified Copper-Iron-based Oil-Containing Bearing

Long-term Ball Milling and Hot Pressing of In-Situ Nanoscale Tungsten Carbides Reinforced Copper Composite and Its Characterization

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

Microstructures and properties of Cu-10Sn oil bearings reinforced by Al2O3 nanoparticles

Sintering Densification of Cu/Al2O3p Nano-Composite Powders by Electroless Copper Plating

Microstructures and properties of Al 2 O 3 dispersion-strengthened Cu10Sn oil bearings prepared by solid-liquid doping and reactive synthesis method

Effect of sintering temperature on microstructure and properties of nano-WC particle reinforced copper matrix composites prepared by hot-pressing sintering

The Influence of the Modification of Carbon Nanotubes on the Properties of Copper Matrix Sintered Materials

Microstructure and Mechanical Properties of Sintered and Forged Fe-2Cu-0.5C-0.11S Materials

Effect of cobalt content on the microstructure, microtexture, and mechanical properties of W-Ni-Fe-xCo alloys during solid-phase-sintering and liquid-phase-sintering

Effect of sintering temperature on fine-grained Cu W composites with high copper

Effect of Cu content on the microstructure and properties of sintered Fe-0.8C-xCu antifriction materials

Effects of a hierarchical pore structure on the tribological properties of an oil-containing iron-based composite

Microstructure and properties of W Cu composites reinforced by in-situ generated WC

Enhanced properties of hard metal WC-Ni processed from nanostructured powders

Mechanical and tribological properties of WC particles reinforced Cu-20Zn matrix composites

Study on the Tribological Performance of Copper-Based Powder Metallurgical Friction Materials with Cu-Coated or Uncoated Graphite Particles as Lubricants

Tensile and Fatigue Characteristics of WC-20wt%Co Cemented Carbide with Sintering Methods

Optimisation of sintering parameters for bonding nanocrystalline cemented tungsten carbide powder and solid high strength steel

Effect of nano-Y2O3 on the microstructure and mechanical properties of Cu-10W composites prepared by spark plasma sintering