Abstract:Antifriction alloys such as AlSn20Cu are key material options for sliding bearings used in machinery. Uniform distribution and a near-equiaxed granularity tin phase are generally considered to be ideal characteristics of an AlSn20Cu antifriction alloy, although these properties vary by fabrication method. In this study, to analyze the variation of the microstructure with the fabrication method, AlSn20Cu alloys are prepared by three methods: semi-continuous casting, semi-solid die casting, and spray forming. Bearing blanks are subsequently prepared from the fabricated alloys using different processes. Morphological information, such as the total area ratio and average particle diameter of the tin phase, are quantitatively characterized. For the tin phase of the AlSn20Cu alloy, the deformation and annealing involved in semi-continuous casting leads to a prolate particle shape. The average particle diameter of the tin phase is 12.6 μm, and the overall distribution state is related to the deformation direction. The tin phase of AlSn20Cu alloys prepared by semi-solid die casting presents both nearly spherical and strip shapes, with an average particle diameter of 9.6 μm. The tin phase of AlSn20Cu alloys prepared by spray forming and blocking hot extrusion presents a nearly equilateral shape, with an average particle diameter of 6.2 μm. These results indicate that, of the three preparation methods analyzed in this study, semi-solid die casting provides the shortest process flow time, whereas a finer and more uniform tin-phase structure may be obtained using the spray-forming process. The semi-solid die casting method presents the greatest potential for industrial application, and this method therefore presents a promising possibility for further optimization.

Microstructures and properties of Al 2 O 3 dispersion-strengthened Cu10Sn oil bearings prepared by solid-liquid doping and reactive synthesis method

Microstructures and properties of Cu-10Sn oil bearings reinforced by Al2O3 nanoparticles

Microstructure and Wear Properties of Al-Based Bearing Alloys Fabricated by Mechanical Alloying

Microstructure Comparison for AlSn20Cu Antifriction Alloys Prepared by Semi-Continuous Casting, Semi-Solid Die Casting, and Spray Forming

First-principles calculations of structural and elastic properties of Sn solid solution, Cu 6 Sn 5 and SnSb in tin-based bearing alloy

Microstructure and compression properties of fine Al2O3 particles dispersion strengthened molybdenum alloy

Simple Synthesis of the Composite Coating and the Lubrication Mechanisms of the Spherical SnAgCu–Al2O3

Microstructure and mechanical properties of Cu-12 Al-6 Ni with Ti addition prepared by powder metallurgy

Enhancement of Wear Properties of Ultrafine-Structured Al–Sn Alloy-Embedded Sn Nanoparticles Through in Situ Synthesis

Microstructure development of Y–Ti–O dispersion strengthened Cu alloys fabricated by mechanical alloying

Improving wear performance of dual-scale Al–Sn alloys by adding nano-Si@Sn: Effects of Sn nanophase lubrication and nano-Si polishing

Strengthening mechanism of in-situ synthesized Cu2S nanoparticles on tribological performance of polyamide-imide bonded solid lubricating coatings

Significant Improvement of Wear Properties by Creating Micro/nano Dual-Scale Structure in Al–Sn Alloys

Investigation on Microstructure and Properties of Cu–Al2O3 Composites Fabricated by a Novel In-Situ Reactive Synthesis

Synthesis and characterization of an in-situ Al2O3/Al–Cu composite with a heterogeneous structure

Regulating the Microstructure and Mechanical Properties in Cast Al–3Li–2Cu-0.15Zr Alloy Via Sn Addition and Heat Treatment

Optimizing the Thermomechanical Process of Nickel-Based ODS Superalloys by an Efficient Method

Preparation and properties of Al2O3 dispersed fine-grained W-Cu alloy

Novel method to achieve synergetic strength–ductility improvement of Al–Cu alloy by in situ TiC–TiB2 particles via direct reaction synthesis

Effect of Ti3SiC2 replacing graphite on the microstructure and properties of Cu-Sn matrix composites

Study on Microstructure of NiAl Matrix High Temperature Lubricating Composites Containing BaO/TiO2 Metallic Oxide