Abstract:Antifriction alloys such as AlSn20Cu are key material options for sliding bearings used in machinery. Uniform distribution and a near-equiaxed granularity tin phase are generally considered to be ideal characteristics of an AlSn20Cu antifriction alloy, although these properties vary by fabrication method. In this study, to analyze the variation of the microstructure with the fabrication method, AlSn20Cu alloys are prepared by three methods: semi-continuous casting, semi-solid die casting, and spray forming. Bearing blanks are subsequently prepared from the fabricated alloys using different processes. Morphological information, such as the total area ratio and average particle diameter of the tin phase, are quantitatively characterized. For the tin phase of the AlSn20Cu alloy, the deformation and annealing involved in semi-continuous casting leads to a prolate particle shape. The average particle diameter of the tin phase is 12.6 μm, and the overall distribution state is related to the deformation direction. The tin phase of AlSn20Cu alloys prepared by semi-solid die casting presents both nearly spherical and strip shapes, with an average particle diameter of 9.6 μm. The tin phase of AlSn20Cu alloys prepared by spray forming and blocking hot extrusion presents a nearly equilateral shape, with an average particle diameter of 6.2 μm. These results indicate that, of the three preparation methods analyzed in this study, semi-solid die casting provides the shortest process flow time, whereas a finer and more uniform tin-phase structure may be obtained using the spray-forming process. The semi-solid die casting method presents the greatest potential for industrial application, and this method therefore presents a promising possibility for further optimization.

First-principles calculations of structural and elastic properties of Sn solid solution, Cu 6 Sn 5 and SnSb in tin-based bearing alloy

First Principles Studies on the Elastic, Thermodynamic Properties and Electronic Structure of Ti15−xMoxSn Compounds

The Structural, Elastic And Thermodynamic Properties Of Intermetallic Phases In Mg-Sn-Si-Ca(Sr) Alloys: A First-Principles Study

Effect of Zr, Hf, and Sn Additives on Elastic Properties of Α2-Ti3al Phase by First-Principles Calculations

Deformation mechanism of various Sn-xBi alloys under tensile tests

Influence on the mechanical properties and electronic structures of Cu-alloyed Ti 5 Sn 3 compounds from first-principles calculations

Mechanical And Thermodynamic Properties Of Mg17la2, La5si4 And La5sn3 Phases In Mg-Sn-Mn(Si)-La Alloy From First-Principles Calculations

Stability and physical properties tuning via interstitials chemical engineering of Zr5Sn3: a first-principles study

Design of Cu–Cr Alloys with High Strength and High Ductility Based on First-Principles Calculations

First-principle and molecular dynamics calculations for physical properties of Ni–Sn alloy system

Microstructure Comparison for AlSn20Cu Antifriction Alloys Prepared by Semi-Continuous Casting, Semi-Solid Die Casting, and Spray Forming

First Principles Investigation of Binary Intermetallics in Mg–Al–Ca–Sn Alloy: Stability, Electronic Structures, Elastic Properties and Thermodynamic Properties

Compressive Rheological Behavior and Microstructure Evolution of a Semi-Solid CuSn10P1 Alloy at Medium Temperature and Low Strain

Microstructures and properties of Cu-10Sn oil bearings reinforced by Al2O3 nanoparticles

First-Principles Calculation Of Electronic Structure And Elastic Property Of Binary Phases In Mg-Al-Sn-Y Alloy

Microstructure and Wear Properties of Al-Based Bearing Alloys Fabricated by Mechanical Alloying

Investigation of the Influence of Alloy Atomic Doping on the Properties of Cu-Sn Alloys Based on First Principles

First Principle Calculation and Thermodynamic Analysis of Coexisting Phase of Cu-Cr-Sn Copper Alloy

Interfacial Endogenous Stress-Induced Phase-Stress Partition in Tin-Lead Dual-Phase Alloy at Cryogenic Temperature

Mechanical Characterization and Deformation Behavior of Β-Stabilized Ti-Nb-Sn-Cr Alloys

First-Principles Calculations of the Mechanical Properties of Doped Cu3P Alloys