Abstract:The dense WC-M2 high-speed steel matrix composites (WC-M2 HSS MMCs) with different WC content were prepared by mechanical alloying and vacuum sintering process. Tungsten Carbide (WC) with 0, 2, 5, 8, and 10 (by weight %) were dispersed in the matrix. The effects of WC content on the densification mechanism, phase composition, microstructure, fracture morphology, and mechanical and wear properties of the sintered composites were systematically investigated. The experimental results showed that at a vacuum sintering temperature of 1260 °C, the composite material specimens achieved near-full densification, with predominant phases being Martensitic, M 7 C 3 , M 6 C, M 2 C, MC, WC, α-Fe, and γ-Fe. Reasonable WC addition has improved grain uniformity and reduced micro-defects, which enhanced the overall mechanical properties. With an increase in WC content, the hardness and relative density of the composites showed a gradual increase, whereas transverse rupture strength and impact toughness initially improved but subsequently decreased. The friction coefficient displayed an initial increase followed by a decrease, while the wear rate showed an opposite trend. The impact fracture morphology is dominated by the interfacial separation between the WC particle phase and the binder phase, supplemented by the plastic tearing of the binder phase. The impact toughness mainly depended on the fracture of the binder phase. During crack propagation, both intergranular and transgranular fractures exist, of which the intergranular fracture prevails and coarse grains are more prone to transgranular fracture. With 5 wt.% WC, the steel matrix composites obtained peak mechanical performance, with impact toughness, bending strength, and hardness measuring 13.2 J cm −2 , 1584.3 MPa, and 780.9 HV, respectively, which also yielded the highest wear resistance.

Effect of the Addition of Nanosized Y2O3 on the Mechanical Properties of WC-Bronze Composites

The Effect Of Zro2 Nanoparticles On The Microstructure And Properties Of Sintered Wc-Bronze-Based Diamond Composites

Effect of WC Nanoparticles on the Microstructure and Properties of WC-Bronze-Ni-Mn Based Diamond Composites

Effect of nano-Y2O3 on the microstructure and mechanical properties of Cu-10W composites prepared by spark plasma sintering

Influence of Nano-Sized La2O3 Addition on the Sintering Behavior and Mechanical Properties of WC–La2O3 Composites

The Effect of Y2O3 Particles on the Microstructure and Mechanical Properties of Tungsten Fiber-Reinforced Tungsten Composites

Effect of Tungsten Carbide Additions on the Microstructure, Mechanical, and Tribological Properties of M2 High-Speed Steel Matrix Composites

The Effect of Cr Addition on the Strength and High Temperature Oxidation Resistance of Y2O3 Dispersion Strengthened Mo Composites

Effect of ZrC nano-powder addition on the microstructure and mechanical properties of binderless tungsten carbide fabricated by spark plasma sintering

Effect of Mo and Y2O3 Additions on the Microstructure and Properties of Fine WC-Co Cemented Carbides Fabricated by Spark Plasma Sintering

Improvements Of Mechanical Properties Of Wc-Zro2 Composites With Addition Of Ultrafine Porous Boron Nitride Nanofiber

Fabrication and Mechanical Properties of Wc-Co-Al2o3 Nanocomposites by Spark Plasma Sintering

Mechanical and tribological properties of WC particles reinforced Cu-20Zn matrix composites

Y2O3- and NbC-doped ultrafine WC–10Co alloys by low pressure sintering

Effect of WC mass fraction on the microstructure and frictional wear properties of WC/Fe matrix composites

Effect of WC Incorporation on the Microstructure and Mechanical Properties of Ni625/WC Spark Plasma Sintered Composites

Effect of yttrium oxide addition on the microstructure and mechanical properties of WC–ni composites fabricated from recycled WC and Ni

Mechanical Properties and Microstructure of Al_2O_3/WC - 8co Nanometer/micron Composites

Effect of Ni Content on Microstructure and Properties of WC-Ni Composites Prepared by Electroless Plating and Powder Metallurgy

Effects of Nano-Al2O3 Additions on Microstructures and Properties of WC-8Co Hard Metals

Effects of Carbon Nanotubes Incorporation on the Grain Growth and Properties of WC/Co Nanocomposites