Abstract:The homogenized Mg-10Gd-1Zn-0.4Zr (wt.%) alloys with and without the LPSO phases were hot extruded, and then the texture evolution, microstructure and mechanical properties of the extruded alloys were investigated. The initial microstructure (prior to extrusion) containing no LPSO phases or only bulk/lamellar LPSO phases leads to a fully dynamically recrystallized (DRXed) grains, while that containing both the bulk and lamellar LPSO phases results in a bimodal structure with the coarse deformed grains and fine DRXed grains, indicating that the bulk LPSO phases can promote the DRX behavior via particle stimulated nucleation mechanism while the lamellar LPSO phases hamper the DRX behavior. An abnormal texture with parallel to the extrusion direction is observed in extruded alloys with a large average grain size, while a relatively weak basal texture is observed in small grains. The formation mechanism of this abnormal texture is due to the growth advantage of the DRXed grains with parallel to the extrusion direction over other grains. The contribution of each strengthening mechanism to the yield strength in four extruded alloys was calculated quantitatively, and the results show that grain refinement and solid solution strengthening mechanisms contribute the most to the yield strength in all extruded alloys. The contributions of dislocation strengthening and the secondary phase strengthening are enhanced in extruded alloys containing bulk LPSO phases, while that of texture strengthening is reduced. This work sheds light on controlling the mechanical properties of the extruded Mg alloys via the LPSO phases and texture.

Influence of texture on the corrosion behavior of an as-extruded Mg–8Al-0.5In alloy sheet

The Effect of Texture on the Corrosion Behavior of AZ31 Mg Alloy

Effect of texture evolution on corrosion resistance of AZ80 magnesium alloy subjected to applied force in simulated body fluid

The synergistic effects of texture and continuous precipitates on the corrosion resistance of AZ80 magnesium alloy

High corrosion resistance and weak corrosion anisotropy of an as-rolled Mg-3Al-1Zn (in wt.%) alloy with strong crystallographic texture

Investigation on corrosion behavior and mechanical properties of an extruded Mg-Zn-Al-Sn-Mn alloy

Study of the corrosion mechanism of Mg–Gd based soluble magnesium alloys with different initial texture states

Thermal Stability of Different Texture Components in Extruded Mg–3Al–1Zn Alloy

Elucidating the dependence of corrosion behavior and mechanical property on the grain structure of low-temperature as-extruded Mg–Zn–Ca–Zr alloy

Effect of grain size and crystal orientation on the corrosion behavior of as-extruded Mg-6Gd-2Y-0.2Zr alloy

Role of bimodal-grained structure with random texture on mechanical and corrosion properties of a Mg-Zn-Nd alloy

Microstructure and corrosion behavior of as-homogenized and as-extruded Mg−xLi−3Al−2Zn−0.5Y alloys (x=4, 8, 12)

Influence of Texture on the Mechanical Properties of a Mg-6Al-1Zn-0.9Sn Alloy Processed by ECAP

The texture and its optimization in magnesium alloy

Anisotropy of the Crystallographic Orientation and Corrosion Performance of High-Strength AZ80 Mg Alloy

Corrosion behavior and mechanical properties of extruded low-alloyed Mg−0.5Bi−0.5Y−0.2Zn alloy

Understanding the weakening of texture in multiaxial forged ultrafine-grained strong and ductile Mg-2Zn-2Gd alloy

Modulation of corrosion properties by heat treatment and extrusion with mechanism analysis of high mechanical strength Mg-5.6Dy-3.1Ni alloy

Microstructure and corrosion properties of Mg–0.5Zn–0.2Ca–0.2Ce alloy with different processing conditions

Effect of Microstructure on the Corrosion Behavior of as-cast and Extruded Mg–Sn–Y Alloys

Texture, microstructure and mechanical properties of an extruded Mg-10Gd-1Zn-0.4Zr alloy: Role of microstructure prior to extrusion