Abstract:The mechanical and twinning behavior of Mg alloys containing a monolithic texture component have been extensively studied; however, studies on samples with multi texture components are much insufficient. In this study, the quantitative relationship between the mechanical behavior under tension along the extrusion direction (ED) of Mg AZ31 rods and the percentages of bimodal texture components <0002>// ED (19–87%) and <0002>⊥ED were systematically studied. The component <0002>// ED favors <math>{101¯2}</math> twinning and is soft orientations; however, the component <0002>⊥ED favors prismatic slip and is hard orientations. The results show that the yield strength does not decrease linearly with an increase in the percentage of the soft orientations and show a deviation from the calculations using the conventional rule of mixtures. A higher percentage of the soft grains increases this deviation when the percentage is below 50%, and decreases it over 50%. The ultimate strengths, however, do not show an obvious dependence on the percentage of the soft orientations. Subsequently, the corresponding mechanisms are discussed and a modified rule of mixtures was developed. Bimodal texture components stimulate the activation of <math>{101¯2}</math> twin variants with a low Schmid factor and the presence of more variants within one grain. Conventional strain accommodation rule was used to analyze this twinning behavior, but it cannot explain the experimental observations. Crystal-plasticity based finite element modeling was employed to analyze this strange twinning behavior. The results indicate that the interaction among twin variants, rather than deformation in neighboring grains, plays a major role in the activation of twins with a low Schmid factor, due to a hard deformation propagation from the soft grains to the hard grains. This finding provides an important complementation to the strain accommodation theory.

The texture and its optimization in magnesium alloy

Tensile mechanical behavior and texture evolution of the weak texture Mg–1Al–0.5Mn–0.3Gd magnesium alloy

Understanding the weakening of texture in multiaxial forged ultrafine-grained strong and ductile Mg-2Zn-2Gd alloy

Texture property and weakening mechanism of Mg-3Al-1Zn alloy by interactive alternating forward extrusion

Effects of Deformation Mechanisms on Texture Evolution and Mechanical Response of the Mg-1Al-0.5Mn-0.3Gd Alloy Under Plane Tension

Texture Evolution and Their Effects on the Mechanical Properties of Duplex Mg–Li Alloy

Improving the tension-compression asymmetry of ZK61 magnesium alloy through texture optimization in combined extrusion

Enhanced ductility and strength of Mg-1Zn-1Sn-0.3Y-0.2Ca alloy achieved by novel micro-texture design

Microstructure and Texture Evolution of the Magnesium Alloy ZMX210 during Rolling and Annealing

Influence of Texture on the Mechanical Properties of a Mg-6Al-1Zn-0.9Sn Alloy Processed by ECAP

Insights into the evolution of texture and mechanical properties during warm rolling and annealing of Mg–2Zn-0.5Ca alloy

Microstructure evolution and mechanical property of Mg-3Al alloys with addition of Ca and Gd during rolling and annealing process

Dynamic Recrystallization, Texture Evolution, and Improved Mechanical Properties of Mg-Y-Zn-V Alloy during Forging and Subsequent Extruding Deformation

Optimizing mechanical properties of magnesium alloys by philosophy of thermo-kinetic synergy: Review and outlook

Effects of extrusion die cavity on the texture components and the associated mechanical properties for ZK60 magnesium alloy

Enhanced grain refinement and texture weakening in Al–Mg–Si alloy through a novel thermomechanical processing

Thermal Stability of Different Texture Components in Extruded Mg–3Al–1Zn Alloy

A quantitative study on mechanical behavior of Mg alloys with bimodal texture components

Texture, microstructure and mechanical properties of an extruded Mg-10Gd-1Zn-0.4Zr alloy: Role of microstructure prior to extrusion

Effect of texture on damping behaviour in ZK60 magnesium alloy

Effect mechanism of texture orientation on mechanical properties and Hall-Petch relationship of CVCDE AZ31 magnesium alloy via crystal plastic finite element method (CPFEM)