Abstract:Microstructure, texture evolution and mechanical properties of extruded Mg-4.58Zn-2.6Gd-0.18Zr alloy were investigated at extrusion temperatures of 260 °C, 280 °C and 300 °C, extrusion ratios of 10, 15 and 30, and ram speeds of 3 mm s−1 and 6 mm s−1, respectively. The results indicated that the as-cast experimental alloy was composed of α-Mg matrix, coarse α-Mg + W(Mg3Zn3Gd2) eutectic and icosahedral quasicrystalline I(Mg3Zn6Gd) phase. A small amount of undissolved W phases were detected after the homogenization treatment at 505 °C up to 16 h, while most I phase dissolved into the α-Mg matrix. The initial crystallites before extrusion were randomly oriented, and showed a typical random texture. After extrusions, all samples exhibited a bimodal microstructure consisting of fine Dynamic recrystallization (DRX) grains and coarse elongated un-DRX grains, and the formation of ultra-fine DRX grains only occurred in the sample with an extrusion ratio of 10 at 260 °C, 3 mm s−1, which was caused by the solute segregation in homogenized billets and non-uniformly distributed W phase during the extrusion process. A fiber texture with {0002} planes and <1̄21̄0> directions paralleled to the extrusion direction was observed to be dominant in all the extruded samples. Furthermore, the increase of extrusion ratio was found to be beneficial for the DRX process and refinement of grain size, and the maximum texture intensity was accordingly weakened, which resulted in a decrease of tensile yield strength but an increase of elongation. With increasing the extrusion temperature or ram speed, both the grain size and DRX fraction gradually increased. Consequently, the texture was randomized and the maximum texture intensity decreased, which led to a reduction of the elongation and tensile yield strength. The tensile failure behaviors under different extrusion conditions were found to be related with the contraction twin lamellas formed in the un-DRX grains and the string-like W phases.

Texture property and weakening mechanism of Mg-3Al-1Zn alloy by interactive alternating forward extrusion

Mechanism of Texture Evolution Propelled by Recrystallization Behavior of Interactively Alternating Forward Extruded AZ31 Magnesium Alloy under Pre-Upsetting Deformation

Recrystallization behavior and texture evolution on extrusion connection process of Mg/Al alloys thickness-oriented bonding sheet

Understanding the weakening of texture in multiaxial forged ultrafine-grained strong and ductile Mg-2Zn-2Gd alloy

Texture and Texture Optimization of Wrought Mg Alloy

Dynamic Recrystallization, Texture Evolution, and Improved Mechanical Properties of Mg-Y-Zn-V Alloy during Forging and Subsequent Extruding Deformation

Tensile mechanical behavior and texture evolution of the weak texture Mg–1Al–0.5Mn–0.3Gd magnesium alloy

Thermal Stability of Different Texture Components in Extruded Mg–3Al–1Zn Alloy

Texture role in the mechanical property improvement contributed by grain refinement for Mg-2.6Nd-0.55Zn-0.5Zr alloy subjected to extrusion process

Microstructure, Texture Evolution and Tensile Properties of Extruded Mg-4.58Zn-2.6Gd-0.16Zr Alloy

Exceptional Texture Evolution Induced by Multi-Pass Cold Drawing of Magnesium Alloy

Effect of initial texture on dynamic recrystallization and deformation mechanisms in AZ31 Mg alloy extruded at 573K

Texture Evolution of Extruded AZ31 Magnesium Alloy Sheets

Dynamic Recrystallization and Texture Evolution of Mg–Y–Zn Alloy During Hot Extrusion Process

Texture Evolution During Dynamic Recrystallization in a Magnesium Alloy at 450 °C

Microstructure, Texture and Mechanical Properties of Extruded AZ31 Mg Alloy During Small Strain Multi-Directional Forging with Gradient Cooling

Texture weakening and ductility improvement of Mg-1.1Mn-0.5Al alloy via medium temperature-high reduction rolling: twinning variants selection and dynamic recrystallization mechanism

The synergistic and interactive effects of slip systems and dynamic recrystallization on the weakening basal texture of Mg-Y-Nd-Zr-Gd magnesium alloy

Effect of Effective Strain Gradient on Texture and Mechanical Properties of Mg–3Al–1Zn Alloy Sheets Produced by Asymmetric Extrusion

Dynamic Recrystallization Mechanism and Texture Evolution During Interactive Alternating Extruded Magnesium Alloy

Analysis of Abnormal Texture and Strengthening Mechanisms of Extruded Mg–Gd–Y–Nd–Zr Alloy