Abstract:Sb2S3 is a promising environmentally‐friendly semiconductor for stable and high efficiency thin film solar cells, but, like many other polycrystalline materials, is limited by non‐radiative recombination and carrier scattering by grain boundaries. Herein, we show how the grain boundary density in Sb2S3 films can be significantly reduced from 1068±40 nm μm−2 (largest grain ∼5 μm) to 327±23 nm μm−2 (largest grain >15 μm) by incorporating an appropriate amount of Ce3+ into the precursor solution for Sb2S3 deposition. Through extensive characterization of the structural, morphological and optoelectronic properties, complemented with computations, we reveal the underlying mechanisms responsible for the increased grain size and improved photovoltaic performance of Sb2S3 solar cells. A critical factor behind the reduction in grain boundary density is the formation of an ultrathin layer of Ce2S3 at the CdS/Sb2S3 interface, which could reduce the interfacial energy and increase the adhesion work between Sb2S3 and the substrate to encourage heterogeneous nucleation of Sb2S3, as well as increase the rate of grain growth. Through a reduction in non‐radiative recombination at grain boundaries and/or the CdS/Sb2S3 heterointerface as well as improved charge‐carrier transport properties at the heterojunction, we achieved high performance Sb2S3 solar cells with a power conversion efficiency reaching 7.66%, and an open‐circuit voltage (VOC) of 796 mV. This VOC is the highest reported thus far for Sb2S3 solar cells. This work provides a strategy to simultaneously regulate the nucleation and growth of Sb2S3 absorber films via in‐situ chemical environment tuning, which can be more broadly applied to other thin film systems to improve their photovoltaic performance. This article is protected by copyright. All rights reserved

Remarkable Sb2Se3 Solar Cell with a Carbon Electrode by Tailoring Film Growth During the VTD Process

Oxygen Content Modulation Toward Highly Efficient Sb2Se3 Solar Cells

Controllable vapor transport deposition of efficient Sb2(S,Se)3 solar cells via adjusting evaporation source area

Optimisation of Sb2S3 thin-film solar cells via Sb2Se3 post-treatment

Quasi-Vertically Oriented Sb 2 Se 3 Thin-Film Solar Cells with Open-Circuit Voltage Exceeding 500 mV Prepared via Close-Space Sublimation and Selenization

Molecular Beam Epitaxy Deposition of In Situ O‐Doped CdS Films for Highly Efficient Sb2(S,Se)3 Solar Cells

Self‐Regulated Growth of Large‐Grain Sb2S3 Thin Films for High‐Efficiency Solar Cells

Sputtered and Selenized Sb2Se3 Thin-Film Solar Cells with Open-Circuit Voltage Exceeding 500 Mv

Selenium‐Rich Sb2(S,Se)3 Thin Films Deposited via Sequential Chemical Bath Deposition for High‐Efficiency Solar Cells

Regulating Deposition Kinetics via A Novel Additive-assisted Chemical Bath Deposition Technology Enables 10.57%-efficient Sb2Se3 Solar Cells

Se-Elemental Concentration Gradient Regulation for Efficient Sb2(S,Se)3 Solar Cells With High Open-Circuit Voltages

Vapor Transport Deposition of Sb 2 (S,Se) 3 Solar Cells with Continuously Tunable Band Gaps

Fabricating High‐Efficiency Sb2(S,Se)3 Solar Cells by Novel Additive‐Assisted Longitudinal Component Engineering

Improved Open‐Circuit Voltage of Sb 2 Se 3 Thin‐Film Solar Cells Via Interfacial Sulfur Diffusion‐Induced Gradient Bandgap Engineering

Optimizing Crystal Orientation and Defect Mitigation in Antimony Selenide Thin-Film Solar Cells through Buffer Layer Energy Band Adjustment

Solvent‐Assisted Hydrothermal Deposition Approach for Highly‐Efficient Sb2(S,Se)3 Thin‐Film Solar Cells

Heterostructured CdS Buffer Layer for Sb2Se3 Thin Film Solar Cell

Improving the performance of Sb2S3 thin-film solar cells by optimization of VTD source-substrate proximity

Hydrazine Hydrate‐Induced Surface Modification of CdS Electron Transport Layer Enables 10.30%‐efficient Sb2(S,Se)3 Planar Solar Cells

Sb2Se3 thin film solar cells in substrate configuration and the back contact selenization

Grain Engineering of Sb2S3 Thin Films to Enable Efficient Planar Solar Cells with High Open‐Circuit Voltage