Abstract:Tunneling oxide passivated contact (TOPCon) solar cells have made a considerable impact on the global photovoltaic (PV) market. Yet, its relatively poorer reliability compared to Passivated Emitter and Rear Contact (PERC) solar cells puts costly limitations on the module bill of materials that can be used. The use of silver/aluminum (Ag/Al) paste for front-side metallization is identified as a key factor contributing to the relatively poor reliability of TOPCon modules, particularly at high temperatures and humidity. However, very recently, laser-assisted firing techniques such as laser-enhanced contact optimization (LECO) that combine conventional co-firing at relatively low temperatures with a subsequent laser treatment have emerged as an appealing alternative to standard one-step cofiring. The main driver for laser-assisted firing is enabling higher power conversion efficiencies ( PCE ). This technique permits the application of screen printing pastes with considerably reduced levels of aluminum (Al), or even the complete exclusion of Al. Consequently, the enhancement in PCE values may not only boost PCE , but may also offer benefits in terms of reliability. This study investigates the impact of Jolywood Special Injected Metallization (JSIM) method on the reliability of TOPCon solar cells. Cell level damp heat testing at 85 °C and 85% relative humidity (DH85) with selected impurities reveals a significant improvement for the JSIM solar cells versus the standard baseline TOPCon cells. Baseline cells experienced rapid degradation, with a substantial (∼92% rel ) loss in PCE attributed to a significant (∼13,000% rel ) increase in series resistance ( R s ) when exposed to sodium chloride (NaCl). Conversely, JSIM cells showcased remarkable resilience, displaying only a modest drop in PCE (∼3.6% rel ) under similar conditions. This work clearly shows that laser-assisted firing processes such as JSIM also significantly improve the reliability of TOPCon solar cells. This improvement is due to the compatibility of these processes with screen printing pastes that have low or zero Al concentration for the TOPCon front. Consequently, this approach enables using more cost-effective materials for TOPCon modules, thereby reducing the overall cost of solar electricity.

Investigation of Laser Doping and Plating Process for Cost-Effective PV Metallization

Comprehensive Study of Light Induced Plating of Nickel and Its Effect on Large Area Laser Doped Crystalline Solar Cells

Experimental Study on the Elimination of Over-Plating Problems in Industrial Manufacturing of Large-Area Acidic-Textured Laser-Doped Multi-Crystalline Solar Cells

Progress of plated metallization for industrial bifacial TOPCon silicon solar cells

Laser Ablation and Ni/Cu Plating Approach for Tunnel Oxide Passivated Contacts Solar Cells with Variate Polysilicon Layer Thickness: Gains and Possibilities in Comparison to Screen Printing

The Investigation of Plating Technologies for Front Fingers of C-Si Solar Cells

Direct Contact Electroplating Sequence Without Initial Seed Layer for Bifacial TOPCon Solar Cell Metallization

Improving the efficiency of crystalline silicon solar cells by an intersected selective laser doping

Experimental study on the direct planar metallization on glass by the particle sputtering in laser-induced plasma-assisted ablation

Laser Direct Activation of Polyimide for Selective Electroless Plating of Flexible Conductive Patterns

Laser Processing Methods for Perovskite Solar Cells and Modules

Laser-doped solar cells exceeding 18% efficiency on large-area commercial-grade multicrystalline silicon substrates

Qualitative Damage Assessment of Laser Contact Opening and Microstructural Evolution at the Rear Contact of a Perc Mono Crystalline Si Solar Cell upon Co-Firing with Si Doped Al Paste

Laser Doping Selective Emitter with Thin Borosilicate Glass Layer for N-Type Topcon Solar Cells

Copper metallization of electrodes for silicon heterojunction solar cells: Process, reliability and challenges

Research on laser-assisted selective metallization of a 3D printed ceramic surface

Formation of Selective Emitter from Phosphorus Diffusion By Laser Doping Process

Enhancing the reliability of TOPCon technology by laser-enhanced contact firing

Improvement of Laser Contact Opening in Bifacial PERC Solar Cells by Optimizing the Dashed Pattern

Review of the Potential of the Ni/Cu Plating Technique for Crystalline Silicon Solar Cells