Abstract:In the past, Mg-Zn alloys prepared by a two-step manufacturing process of casting plus extrusion have been demonstrated to be a good candidate for biodegradable applications. But, studies on fabricating of Mg-Zn alloys with a single step process of squeeze casting capable of producing porosity-free Mg alloys, which can reduce the cost, are limited. In the present work, Zinc (Zn) addition varying from 1.0 up to 10.0 wt. % was introduced into liquid magnesium. The alloyed liquid was squeeze cast under an applied pressure of 90 MPa. The results of mechanical testing on the squeeze cast Mg-Zn alloys shows that Zn is an effective additive for enhancing their mechanical properties, specifically, tensile and yield strengths at room temperature, but reducing the elongation. While the Zn addition rises from 1.0 to 10.0 wt.%, the ultimate tensile and yield strengths increases to 181.0 MPa and 105.0 MPa from 140.7 MPa and 39.3 MPa, while the elongation-to-failure (e f ) decreases to 3.7% from 6.2%, respectively. The reveal of the as-cast grain structure by an optical microscope (OM) indicates that the high Zn content reduces grain sizes considerably. The microstructures analyzed by a scanning electron microscope (SEM) with the energy dispersive spectroscopy (EDS) show that the secondary MgZn phase forms once Zn is introduced in sufficient amount. The grain refinement and the massive presence of the secondary MgZn phase at the boundaries of the refined grains should be responsible to the enhancement of the strengths and the reduction in the elongation. The developed pressurized casting without employing secondary manufacturing processes such as extrusion or heat treatment exhibits its advantages to enhance the mechanical properties of the Mg alloys with high Zn content over conventional fabrication processes, since high Zn-containing Mg alloys have a long freezing range and tend to form microshrinkage porosity.

Preparation and Rheo-Squeeze Casting of Semi-Solid AZ91–2 Wt% Ca Magnesium Alloy by Gas Bubbling Process

Semi-solid Slurry Preparation, Rheo-Die Casting and Rheo-Squeeze Casting of an AZ91–2Ca–1.5Ce Ignition-Proof Magnesium Alloy by Gas-Bubbling Process

Microstructure and Mechanical Properties of Rheo-Squeeze Casting Az91-Ca Magnesium Alloy Prepared by Gas Bubbling Process

Study on Pressurized Solidification Behavior and Microstructure Characteristics of Squeeze Casting Magnesium Alloy AZ91D

Effects of processing parameters and Ca content on microstructure and mechanical properties of squeeze casting AZ91-Ca alloys

Microstructure and Mechanical Properties of Squeeze Casting Quasicrystal Reinforced AZ91D Magnesium Matrix Composites

Experimental study of squeeze casting of ZK60 magnesium alloy

Effect of Ca Content and Rheo-Squeeze Casting Parameters on Microstructure and Mechanical Properties of AZ91−1Ce−xCa Alloys

Microstructure Evolution and Mechanical Properties of Rheo-Squeeze Casting AZ91-Ca Alloy During Heat Treatment

Study on a Semi-Solid Rheo-Diecasting Process With AZ91D Alloy Slurry

Study on Semisolid Rheo-Diecasting Process, Microstructure and Mechanical Properties of Mg-6Al-1Ca-0.5Sb Alloy with High Solid Fraction

Effects of Processing Parameters on Microstructure of Semi-Solid Slurry of AZ91D Magnesium Alloy Prepared by Gas Bubbling

Microstructure and Properties of Mg-5Al-1.5Ca-0.4Zn Based Alloyby Semi-Solid Isothermal Heat-Treatment-die-pressure-casting Process

Preparation of Az91d Magnesium Alloy Semi-Solid Billet by New Strain Induced Melt Activated Method

Study on Processing Conditions for Semi-Solid Forging of Magnesium Alloys

Microstructure and mechanical property of semi-solid magnesium alloy fabricated by twin-screw stirring

Al-CeO2-Mg refiner on grain refinement, cast fluidity and mechanical properties of AZ91 alloy

Squeeze Cast Mg-Zn Alloys for Bioapplications: Tensile Properties and Microstructure

Preparation of Mg-Al Series Magnesium Alloy Semi-solid Billets and its Thixo-extrusion Forming

Effects of processing parameters on microstructure and mechanical properties of squeeze-cast Mg–12Zn–4Al–0.5Ca alloy

Selective laser melted AZ91D magnesium alloy with superior balance of strength and ductility