Abstract:Fine-grained metals have attracted much interest due to the possibility to obtain both high strength and high ductility.Studies of the deformation mechanisms in fine-grained metals are therefore important,and can also help fill a gap in knowledge between nano-grained metals and conventional coarse-grained metals,which is an area of both scientific and industrial interest.For such an investigation it is very important to use a starting material with a simple microstructure.For this purpose spark plasma sintering(SPS) has been used to prepare samples of fully dense,fine-grained Al with average grain sizes ranging from 0.8μm to 5.2μm,in a fully recrystallized condition,with equiaxed grains and a random texture.The microstructures and mechanical properties of these sintered finegrained Al samples have been studied using EBSD,TEM and compression testing.Based on these studies,relationships between the microstructure and mechanical properties have been established. The results show that the formation of deformation microstructure depends on grain size.During deformation,all grains in samples with an average grain size of 5.2μm show grain subdivision by dislocation boundary formation,though few grains in a sample with an average grain size of 0.8μm show dislocation boundary formation.The mechanical properties of fine-grained Al show a transition in behavior with decreasing average grain size.For samples with an average grain size of 1.3μm,stressstrain curves show yield drop phenomenon,attributed to source-limited hardening.For a sample with an average grain size of 0.8μm,the stress-strain curve shows only limited work-hardening after yielding,in agreement with the observation of the limited formation of dislocation boundaries inside grains during deformation.For a sample with average grain size of 5.2μm the average dislocation boundary misorientation angle increases more quickly than in deformed conventional coarse-grained Al deformed to the same strain,due to the effect of increased volume fraction of grain boundaries and oxide particles.The strength of the SPS-prepared Al samples is higher than found for samples with identical grain sizes prepared by thermo-mechanical deformation,due to the presence of oxide particles,and to source-limited hardening for samples with average grain sizes smaller than 1.3μm.

Effects of Annealing and Extrusion on the Microstructure and Tensile Properties of Ultrafine-Grained Al Fabricated by Spark Plasma Sintering

Achieving a Compatible Tensile Strength and Ductility of Bulk Ultrafine Grained Al by Spark Plasma Sintering Plus Annealing

Microstructures and Mechanical Properties of Sintered Fine-Grained Al

Microstructure and mechanical properties of Ti-43Al-9V alloy fabricated by spark plasma sintering

Microstructures and Mechanical Properties of TiAl Alloy Prepared by Spark Plasma Sintering

Effect of spark plasma sintering temperature on microstructure and mechanical properties of melt-spun TiAl alloys

Microstructure and mechanical properties of ultrafine grained Cu-0.8 wt%C alloy with a bimodal microstructure produced by powder metallurgy techniques

The Microstructure Evolution, Mechanical Properties and Densification Mechanism of Tial-Based Alloys Prepared by Spark Plasma Sintering

Effects of Annealing on the Microstructure and Mechanical Properties of Selective Laser Melted AlSi7Mg Alloy

Microstructure, Densification and Mechanical Properties of Ti-22Al-25Nb Alloy Fabricated by Spark Plasma Sintering

Effect of Spark Plasma Sintering Temperature on the Microstructure and Mechanical Properties of A Ti2alc/Tial Composite

Microstructural Evolution and Mechanical Properties of a High Yttrium Containing TiAl Based Alloy Densified by Spark Plasma Sintering

Graded Microstructure and Mechanical Properties of Spark Plasma Sintered Fe-Cr alloys

Synthesis and Properties of an Ultrafine Grained Ti-45al-2cr-2nb-1b-0.5ta Alloy Prepared by Double Mechanical Milling and Spark Plasma Sintering

Microstructure and Mechanical Properties of Tial-Based Alloy Prepared by Double Mechanical Milling and Spark Plasma Sintering

Synthesis, characterization, and mechanical behavior of ultra-fine-grained Ti-6Al-5V alloy prepared by mechanical alloying and spark plasma sintering

Effect of Annealing on Microstructure and Tensile Properties of Selective Laser Melting MAR-M509 Superalloy

Effect of microstructural evolution on mechanical properties and fracture modes of AlSi10Mg blocks fabricated by selective laser melting after stress relief annealing

Microstructures and Mechanical Properties of Ti-43Al-5V-4Nb-Y Alloy Consolidated by Spark Plasma Sintering

Enhanced Combination of Strength and Ductility in Ultrafine-Grained Aluminum Composites Reinforced with High Content Intragranular Nanoparticles

Microstructure Evolution and Mechanical Properties of ODS FeCrAl Alloys Fabricated by Spark Plasma Sintering