Abstract:The optimization of back contact interface is crucial to improve the performance of Cu2ZnSnS4 (CZTS) thin film solar cells. In this paper, we first employ Al-doped ZnO (AZO) as the intermediate layer into the Mo/CZTS interface to improve the quality of back contact region. This AZO intermediate layer, obtained from the sputtering method prior to the CZTS precursor deposition, initially blocks the direct contact of CZTS with the Mo layer and thus indeed suppresses the decomposition reaction between Mo and CZTS. Consequently, the generation of voids at the back contact region is obviously avoided. Besides, the AZO intermediate layer can inhibit the reaction between sulfur (S) and Mo during sulfurization process, and thus significantly reduce the thickness of MoS2. Meanwhile, the AZO intermediate layer with suitable thickness does not affect the crystal quality of CZTS absorber layer. Moreover, the effects of different thicknesses of predeposited AZO on the film morphology, composition, and corresponding device performance were systematically studied. After optimizing the thickness of the AZO layer, the efficiency of the resultant device has increased from 7.1% to 8.4% (the active area efficiency is 9.2%).The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c18799?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c18799</a>.XRR patterns of 15, 30, 45, and 60 nm AZO films deposited on SLG; relevant formula and description of how to calculate the film thickness from XRR mode of XRD; EDS mapping for surface of four CZTS films with 0 nm AZO, 10 nm AZO, 20 nm AZO, and 30 nm AZO and EDS mapping for cross-sectional of CZTS films with 30 nm AZO; statistical box charts of typical parameters of CZTS devices with different thicknesses of AZO at back contact region; cross-sectional SEM images of four CZTS devices with different thicknesses of AZO at back contact region; and comparison of different intermediate layers for CZTS cells (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c18799/suppl_file/am0c18799_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Band Alignment Tuning at Mo/CZTS Back Contact Interface Through Surface Oxidation States Control of Mo Substrate

Investigation in Feasibility of Molybdenum As A Back Contact Layer for Silicon Based Quantum Dot Solar Cells

Back Contact Engineering to Improve CZTSSe Solar Cell Performance by Inserting MoO3 Sacrificial Nanolayers

Modification of Back Contact in Cu2ZnSnS4 Solar Cell by Inserting Al-Doped ZnO Intermediate Layer.

Modification of Back Contact in Cu 2 ZnSnS 4 Solar Cell by Inserting Al-Doped ZnO Intermediate Layer

The Effect of Thermal Evaporated MoO3 Intermediate Layer As Primary Back Contact for Kesterite Cu2ZnSnS4 Solar Cells

Improvement of Efficiency in Kesterite Solar Cells by Intentionally Inserting a Thin MoS2 Layer into the Back Interface.

Energy Band Alignment in Molybdenum Oxide/Cu(In,Ga)Se2 Interface for High-Efficiency Ultrathin Cu(In,Ga)Se2 Solar Cells from Low-Temperature Growth

Exploring the effect of oxygen environment on the Mo/CdTe/CdSe solar cell substrate configuration

MoO<sub>2</sub> Sacrificial Layer for Optimizing Back Contact Interface of Cu<sub>2</sub>ZnSn(S,Se)<sub>4</sub> Solar Cells

Characterization of Sputtered MoOx Thin Films with Different Oxygen Content and Their Application As Back Contact in CdTe Solar Cells

Improving Cu2ZnSnS4 (CZTS) solar cell performance by an ultrathin ZnO intermediate layer between CZTS absorber and Mo back contact

Improvement of Mo/Cu2ZnSnS4 Interface for Cu2ZnSnS4 (CZTS) Thin Film Solar Cell Application

Inhibiting Mos2 Formation by Introducing A Zno Intermediate Layer for Cu2znsns4 Solar Cells

Enhancing the Cu2znsns4 Solar Cell Efficiency by Back Contact Modification: Inserting A Thin Tib2 Intermediate Layer at Cu2znsns4/Mo Interface

Oxygen Promotes the Formation of MoSe2 at the Interface of Cu2ZnSnSe4/Mo.

Low Oxygen Content MoOx and SiOx Tunnel Layer Based Heterocontacts for Efficient and Stable Crystalline Silicon Solar Cells Approaching 22% Efficiency

Flexible Kesterite Cu2ZnSnS4 Solar Cells with Sodium-Doped Molybdenum Back Contacts on Stainless Steel Substrates

Enhancing the performance of Cu<sub>2</sub>ZnSnS<sub>4</sub> solar cell fabricated via successive ionic layer adsorption and reaction method by optimizing the annealing process

Mechanism for Improving Kesterite Solar Cells Performance via Filed Passivation Effect Induced by V-Doped MoSe<sub>2</sub> Interface Layer at Back Interface

Facile Tailor on the Surface of Mo Foil Toward High‐Efficient Flexible CZTSSe Solar Cells