Abstract:Quartz is a widely used material in the field of microelectromechanical systems (MEMS) for fabricating devices such as substrates, probes, and lenses; it is also indispensable as a resonator or oscillator for frequency control in communication and network technologies. However, its development is limited because it is difficult to fabricate an ideal profile for implementation in complex structures. In practice, wet etching is the most effective and extensive method for achieving the expected structure, although dry etching and other special machining techniques have also been investigated. In this study, the dynamic wet etching process was recorded using different ratios of buffered oxide etcher (BOE) solutions as the etchant to reveal the etching mechanism. The experiments were first designed considering the fabrication of samples, experimental conditions, and measurement indicators. Subsequently, the corresponding etch rate, roughness, and surface morphology were investigated to control the process parameters during wet etching. Different etchants exhibit varying etching rates and roughness properties. A smaller proportion of hydrofluoric acid in the BOE solution results in lower etch rate, and vice versa. The roughness (Ra) in the stable stage was not completely consistent with the tendency of the etch rate, whereas the surface morphology and dimensions of the pyramids rationally complied with the roughness trend. Additionally, the results suggested that the three following stages exist during the wet etching process of the z-cut α-quartz wafer; smooth, incremental, and stable. The analysis of the dynamic wet etching process in this study is beneficial for the structural design, manufacturing, and performance of quartz MEMS devices.

Wet Etching: Controlling the Facet of ZnO During Wet Chemical Etching Its (0001¯) O‐Terminated Surface (small 14/2020)

Controlling the Facet of ZnO During Wet Chemical Etching Its (0001¯) O‐Terminated Surface

A Facile Method to Fabricate Superhydrophobic ZnO Nanostructure with Petal Effect

Wet Chemical Etching of ZnO Film Using Aqueous Acidic Salt

Wet Etching in β-Ga2O3 Bulk Single Crystal

Unraveling Anisotropic and Pulsating Etching of ZnO Nanorods in Hydrochloric Acid via Correlative Electron Microscopy

Direct Spectroscopic Evidence on the Photocatalytic Activities of Different ZnO Crystal Facets Toward Photo-Induced Decomposition of CH2O

In Situ Study Wet Chemical Etching of ZnO Nanowires with Different Diameter and Polar Surfaces by LCTEM

In Situ Study of Wet Chemical Etching of ZnO Nanowires with Different Diameters and Polar Surfaces by LCTEM

Control of Wettability on ZnO Thin Film

A Two-step Wet Etching Process of PZT Thin Film With Ultra-low Undercut for MEMS Applications

Effect of wet chemical etching on femtosecond laser fabricated surface microstructure of polycrystalline ZnS

Texture-etched broad surface features of double-layered ZnO:Al transparent conductive films for high haze values

Optical, Surface Charge State and Photocatalysis Study of ZnO with Different Exposure Faces

Dynamic Process of Wet Etching Using BOE Solutions to Control the Etch Rate, Roughness, and Surface Morphology of a Z-cut Α-Quartz Wafer

Formation mechanism of homo-epitaxial morphology on ZnO (000 ± 1) polar surfaces

Study on Wet-etching of PZT Thin Films

Superior Photocatalytic Activity of Porous Wurtzite ZnO Nanosheets with Exposed {0 0 1} Facets and a Charge Separation Model Between Polar (0 0 1) and (001¯) Surfaces

Monoclinic Tungsten Oxide With {100} Facet Orientation And Tuned Electronic Band Structure For Enhanced Photocatalytic Oxidations

"Magic" Vicinal Zinc Oxide Surfaces.

Surface Energy Guided Sub-10 Nm Hierarchy Structures Fabrication by Direct E-Beam Etching